Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM
RM38G0E _52 Drivetrain _100437 JF2BM TRANSFER / 4WD / AWD _0467431 TRANSFER SYSTEM J

JF2BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  Front Differential Lock Switch Circuit  


WIRING DIAGRAM

C339930E15
3.542,2.698 3.948,2.938 0.406,0.24 10 false B9 0.656,2.677 2.865,2.948 2.208,0.271 10 false Front Differential Lock Switch 0.646,2.458 1.104,2.688 0.458,0.229 10 false I90 0.948,1.854 1.344,2.073 0.396,0.219 10 false FRE 2.063,1.844 2.385,2.063 0.323,0.219 10 false FRB 2.5,1.802 2.729,2.021 0.229,0.219 10 false 5 0.646,1.813 0.844,2.052 0.198,0.24 10 false 2 0.865,3.365 2.677,3.583 1.813,0.219 10 false : CAN Communication Line 3.542,2.938 5.448,3.146 1.906,0.208 10 false 4 Wheel Drive Control ECU 3.438,1.833 3.698,2.021 0.26,0.188 10 false 5 3.729,1.823 4.031,1.99 0.302,0.167 10 false F 4.427,0.823 4.771,1.063 0.344,0.24 10 false IGR 5.75,2.656 6.948,3.125 1.198,0.469 10 false Combination Meter Assembly

PROCEDURE

1.CHECK FRONT DIFFERENTIAL LOCK INDICATOR LIGHT
a.

Turn the ignition switch to ON.


b.

Press the front differential lock switch.


c.

Check the front differential lock indicator light.


Result:
Result Proceed to

Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

Front differential lock indicator light blinks or illuminates A
Front differential lock indicator light remains off regardless of switch operation B
Front differential lock indicator light remains illuminated regardless of switch operation C


d.

Turn the ignition switch off.



A

END

B

2.CHECK CAN COMMUNICATION LINE

C

7.CHECK CAN COMMUNICATION LINE
2.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.

CAN Bus Check
50007
OK:

"Bus Check" indicates no malfunctions in CAN communication.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (FRONT DIFFERENTIAL LOCK CONTROL SWITCH)

NG

3.READ VALUE USING GTS (FRONT DIFFERENTIAL LOCK CONTROL SWITCH)
a.

Turn the ignition switch to ON.


b.

According to the display on the GTS, read the Data List.

Powertrain > Four Wheel Drive > Data List
Tester Display
Front Differential Lock Control Switch
50003 442 20
Powertrain > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Differential Lock Control Switch Front differential lock switch status OFF or ON OFF: Not pressed
ON: Pressed and held
-
OK:

Display changes according to front differential lock switch operation



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

4.INSPECT COMBINATION METER ASSEMBLY (4WD LOCK INDICATOR)

NG

5.INSPECT FRONT DIFFERENTIAL LOCK SWITCH
4.INSPECT COMBINATION METER ASSEMBLY (4WD LOCK INDICATOR)
a.

Using the GTS, perform the Active Test "4WD Lock Indicator" of the combination meter assembly.

Body Electrical > Combination Meter > Active Test
Tester Display
4WD Lock Indicator
50004 409 100

OK:

Perform an Active Test of the combination meter assembly using the GTS


Result:
Proceed to
OK
NG



OK

NG

5.INSPECT FRONT DIFFERENTIAL LOCK SWITCH
a.

Inspect the front differential lock switch.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT DIFFERENTIAL LOCK CONTROL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - FRONT DIFFERENTIAL LOCK SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - FRONT DIFFERENTIAL LOCK SWITCH)
a.

Disconnect the B9 4 wheel drive control ECU connector.


b.

Disconnect the I90 front differential lock switch connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B9,I90)Location & Routing

Click Connector(B9)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

Click Connector(I90)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Front Differential Lock Switch

B9-5 (F) - I90-5 (FRB) Always Below 1 Ω
I90-2 (FRE) - Body ground Always Below 1 Ω
B9-5 (F) or I90-5 (FRB) - Body ground Always 10 kΩ or higher


d.

Connect the I90 front differential lock switch connector.


e.

Connect the B9 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus.

CAN Bus Check
50007
OK:

"Bus Check" indicates no malfunctions in CAN communication.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (FRONT DIFFERENTIAL LOCK INDICATOR REQUEST)

NG

8.READ VALUE USING GTS (FRONT DIFFERENTIAL LOCK INDICATOR REQUEST)
a.

Turn the ignition switch to ON.


b.

According to the display on the GTS, read the Data List.

Powertrain > Four Wheel Drive > Data List
Tester Display
Front Differential Lock Indicator Request
50003 442 42

c.

Turn the front differential lock switch on and off several times and check the GTS display condition of the front differential lock indicator light.

Powertrain > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Differential Lock Indicator Request Front differential lock indicator light request OFF, ON, Blink1, Blink2 or Blink3 OFF: Indicator light turns off
ON: Indicator light illuminates
Blink1: Indicator light blinks
Blink2: Indicator light blinks 3 times
Blink3: Indicator light rapidly blinks
·

Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)



Result:
Result Proceed to
Data List continues to display ON even when differential lock switch is operated A
Data List display changes according to differential lock switch operation B


d.

Turn the ignition switch off.



A

B