| Procedure | Part Name Code |
|
|
|
|
| 1 | NO. 1 COOLER UNIT DRAIN HOSE | 88539 | - | - | - |
| 2 | NO. 1 COOLER THERMISTOR | 88625 | ( ) |
- | - |
| 3 | NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY | 88501 | ( ) |
- | - |
| *1 | HEATER CASE (for Front Side) | *2 | HEATER CASE (for Rear Side) |
| ● | Non-reusable part |
|
Compressor oil ND-OIL 8 or equivalent |
| *A | for 4 Zone Type | *B | for Dual Type |
| *A | w/ Cool Box | *B | w/o Cool Box |
| *C | w/ PTC Heater | *D | w/o PTC Heater |
| *1 | PIPING CLAMP | *2 | BRACKET |
| *3 | NO. 1 COOLER COVER | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Compressor oil ND-OIL 8 or equivalent | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 22 | COOLER THERMISTOR (ROOM TEMPERATURE SENSOR) | 88625Q | - | - | - |
| 23 | ASPIRATOR | 88897P | - | - | - |
| 24 | BLOWER ASSEMBLY | 87130D | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
88539 1.INSTALL NO. 1 COOLER UNIT DRAIN HOSE
88501 3.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
Remove the vinyl tape from the No. 1 cooler evaporator sub-assembly and then apply a sufficient amount of compressor oil to 2 new O-rings and the fitting surface with the No. 1 cooler evaporator.
ND-OIL 8 or equivalent
Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
Install the No. 1 cooler evaporator sub-assembly to the heater case.
| *a | No. 1 Cooler Thermistor Lead Wire | - | - |
|
Secure the Lead Wire between Guide | - | - |
While inserting the No. 1 cooler thermistor into the guide, insert the guide and attach the claw as shown in the illustration.
Install the heater case with the 2 screws.
87050F 4.INSTALL NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
| *A | for 4 Zone Type | *B | for Dual Type |
Align the direction of the fitting on the heater case to the fitting on the No. 4 air conditioning radiator damper servo sub-assembly as shown in the illustration.
Install the No. 4 air conditioning radiator damper servo sub-assembly with the 3 screws.
87050H 5.INSTALL NO. 6 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for 4 Zone Type)
Align the direction of the fitting on the heater case to the fitting on the No. 6 air conditioning radiator damper servo sub-assembly as shown in the illustration.
Install the No. 6 air conditioning radiator damper servo sub-assembly with the 3 screws.
87050G 6.INSTALL NO. 5 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
| *a | Matchmarks | - | - |
Make sure that the servo motor gear is installed at the position shown in the illustration.
Align with the matchmarks on the gear as shown in the illustration.
Align the guide and install the No. 5 air conditioning radiator damper servo sub-assembly with the 2 screws.
87050E 7.INSTALL NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Align the direction of the fitting on the heater case to the fitting on the No. 3 air conditioning radiator damper servo sub-assembly as shown in the illustration.
Install the No. 3 air conditioning radiator damper servo sub-assembly with the 2 screws.
87050C 8.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Align the direction of the fitting on the heater case to the fitting on the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.
Install the No. 1 air conditioning radiator damper servo sub-assembly with the 3 screws.
87050D 9.INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
| *A | for 4 Zone Type | *B | for Dual Type |
Align the direction of the fitting on the heater case to the fitting on the No. 2 air conditioning radiator damper servo sub-assembly as shown in the illustration.
Install the No. 2 air conditioning radiator damper servo sub-assembly with the 3 screws.
82210K 10.INSTALL AIR CONDITIONING HARNESS ASSEMBLY
88515 11.INSTALL COOLER EXPANSION VALVE (w/o Cool Box)
| *1 | No. 1 Cooler Cover | - | - |
|
Install in this Direction (1) | Install in this Direction (2) |
Install the cooler expansion valve using the following procedure.
1. Remove the vinyl tape from the cooler expansion valve and then install the No. 1 cooler cover to the cooler expansion valve.
3. Install the cooler expansion valve together with the No. 1 cooler cover.
Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed.)
88710B 12.INSTALL AIR CONDITIONING TUBE ASSEMBLY
w/ Cool Box:
| *a | Screw (A) | *b | Screw (B) |
|
Install in this Direction | - | - |
Install the air conditioning tube assembly using the following procedure.
1. Temporarily tighten the air conditioning tube assembly with the hexagon bolt and screw (B).
Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed.)
2. Using a 4 mm hexagon socket wrench, tighten the air conditioning tube assembly with the 2 hexagon bolts.
3. Install a part of the packing as shown in the illustration.
4. Tighten the screw (B).
5. Temporarily tighten the bracket with the hexagon bolt and screw (A).
6. Using a 4 mm hexagon socket wrench, tighten the hexagon bolt.
7. Tighten the screw (A).
w/o Cool Box:
Install the air conditioning tube assembly using the following procedure.
1. Remove the vinyl tape from the air conditioning tube assembly and then apply a sufficient amount of compressor oil to 2 new O-rings and the fitting surface of the cooler expansion valve and air conditioning tube assembly.
ND-OIL 8 or equivalent
2. Install the 2 O-rings to the air conditioning tube assembly.
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
3. Using a 4 mm hexagon socket wrench, tighten the air conditioning tube assembly with the 2 hexagon bolts.
Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed.)
88892N 13.INSTALL NO. 2 COOLER COVER (w/o Cool Box)
88710A 14.INSTALL AIR CONDITIONING TUBE ASSEMBLY (w/ Cool Box)
Install the air conditioning tube assembly using the following procedure.
1. Remove the vinyl tape from air conditioning tube assembly and then apply a sufficient amount of compressor oil to 2 new O-rings and the fitting surface of the air conditioning tube assembly and air conditioning tube assembly.
ND-OIL 8 or equivalent
2. Install the 2 O-rings to the air conditioning tube assembly.
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
3. Install the liquid tube with the screw.
Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed.)
| *a | Correct | *b | Incorrect |
| *c | No Gap | *d | Gap |
Install the piping clamp to the air conditioning tube assembly and air conditioning tube assembly as shown in the illustration.
Make sure that the piping clamp is engaged securely with no gap.
87107A 15.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
87124B 16.INSTALL HEATER CLAMP
87201B 17.INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY
87710G 18.INSTALL QUICK HEATER ASSEMBLY (w/ PTC Heater)
|
Install in this Direction | - | - |
Attach the claw and install the quick heater assembly as shown in the illustration.
| *a | Element |
| *b | Fin |
Do not hold the quick heater assembly by the element or fin. Also, do not damage the quick heater assembly.
Foul odors may occur due to oil adhering to the quick heater assembly.
Check that the heights of the claw fitting surface on the heater case and the claw of the quick heater assembly are aligned.
Install the screw.
87114B 19.INSTALL HEATER COVER (w/o PTC Heater)
Use the same procedure as for the quick heater assembly.
88898D 20.INSTALL GROMMET
87128B 21.INSTALL NO. 2 INSTALL HEATER GROMMET
88625Q 22.INSTALL COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)
88897P 23.INSTALL ASPIRATOR
87130D 24.INSTALL BLOWER ASSEMBLY