Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM38G0E _55 Steering _100923 STEERING COLUMN _0468603 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM J

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  Tilt and Telescopic Manual Switch Circuit  


DESCRIPTION

Different voltage values are sent to the multiplex tilt and telescopic ECU by operating the tilt and telescopic switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should operate based on the voltage value.

WIRING DIAGRAM

C240527E91
4.917,3.875 7.073,4.188 2.156,0.313 10 false Multiplex Tilt and Telescopic ECU 1.458,3.75 3.583,3.906 2.125,0.156 10 false Tilt and Telescopic Switch 3.75,2.646 4.115,2.802 0.365,0.156 10 false MSW 3.906,1 4.125,1.156 0.219,0.156 10 false VC 5.125,2.75 5.49,2.906 0.365,0.156 10 false MSW 5.135,1.094 5.354,1.25 0.219,0.156 10 false VC 0.708,1.906 1.333,2.375 0.625,0.469 10 false TILT DOWN 1.573,1.896 2.25,2.458 0.677,0.563 10 false TELESCO SHORTEN 2.448,1.979 2.979,2.281 0.531,0.302 10 false TILT UP 3.333,1.885 4.031,2.469 0.698,0.583 10 false TELESCO STRETCH 4.927,1 5.104,1.167 0.177,0.167 10 false 5 4.865,2.646 5.104,2.813 0.24,0.167 10 false 18 4.917,3.698 5.385,3.896 0.469,0.198 10 false I43 1.458,3.563 1.948,3.781 0.49,0.219 10 false I46 4.177,2.646 4.354,2.813 0.177,0.167 10 false 3 4.177,1 4.354,1.167 0.177,0.167 10 false 1

PROCEDURE

1.READ VALUE USING GTS (TILT MANUAL SWITCH UP/DOWN, TELESCOPIC MANUAL SWITCH SHORT/LONG)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Tilt&Telescopic > Data List
Tester Display
Tilt Manual Switch Up
Tilt Manual Switch Down
Telescopic Manual Switch Short
Telescopic Manual Switch Long
50003 406 18,19,20,21
Body Electrical > Tilt&Telescopic > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tilt Manual Switch Up Input state of tilt up switch OFF or ON ON: When tilt and telescopic switch up operation performed -
Tilt Manual Switch Down Input state of tilt down switch OFF or ON ON: When tilt and telescopic switch down operation performed -
Telescopic Manual Switch Short Input state of telescopic contract switch OFF or ON ON: When tilt and telescopic switch short operation performed -
Telescopic Manual Switch Long Input state of telescopic extend switch OFF or ON ON: When tilt and telescopic switch long operation performed -
OK:

The value of each Data List item changes in accordance with the operation of the switch.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH)
a.

Disconnect the I43 multiplex tilt and telescopic ECU connector.


b.

Disconnect the I46 tilt and telescopic switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I43,I46)Location & Routing

Click Connector(I43)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multiplex Tilt & Telescopic ECU

Click Connector(I46)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Tilt & Telescopic Switch

I43-5 (VC) - I46-1 (VC) Always Below 1 Ω
I43-18 (MSW) - I46-3 (MSW) Always Below 1 Ω
I43-5 (VC) or I46-1 (VC) - Body ground Always 10 kΩ or higher
I43-18 (MSW) or I46-3 (MSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)
a.
C401145C45
1.458,0.26 1.875,0.5 0.417,0.24 0.927,1.635 1.156,1.146 true 1.156,0.896 0.938,0.542 true 1.583,0.302 2.042,0.5 0.458,0.198 10 false I43 0.813,0.385 1.271,0.583 0.458,0.198 10 false VC 0.729,1.667 1.188,1.865 0.458,0.198 10 false MSW 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)


Reconnect the I43 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I43)Location & Routing

Click Connector(I43)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multiplex Tilt & Telescopic ECU

I43-5 (VC) - I43-18 (MSW) Ignition switch ON 4.9 to 5.1 V



Result:
Proceed to
OK
NG



OK

4.CHECK TILT AND TELESCOPIC SWITCH

NG

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

4.CHECK TILT AND TELESCOPIC SWITCH

OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE TILT AND TELESCOPIC SWITCH