Different voltage values are sent to the multiplex tilt and telescopic ECU by operating the tilt and telescopic switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should operate based on the voltage value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B26031C | Tilt and Telescopic Manual Switch Circuit Circuit Voltage Out of Range | When operating the tilt and telescopic switch, an abnormal voltage value is sent to the multiplex tilt and telescopic ECU. |
·
Tilt and telescopic switch
·
Harness or connector
·
Multiplex tilt and telescopic ECU |
Tilt&Telescopic | A |
Read the Data List according to the display on the GTS.
| Tester Display |
|---|
| Tilt Manual Switch Up |
| Tilt Manual Switch Down |
| Telescopic Manual Switch Short |
| Telescopic Manual Switch Long |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tilt Manual Switch Up | Input state of tilt up switch | OFF or ON | ON: When tilt and telescopic switch up operation performed | - |
| Tilt Manual Switch Down | Input state of tilt down switch | OFF or ON | ON: When tilt and telescopic switch down operation performed | - |
| Telescopic Manual Switch Short | Input state of telescopic contract switch | OFF or ON | ON: When tilt and telescopic switch short operation performed | - |
| Telescopic Manual Switch Long | Input state of telescopic extend switch | OFF or ON | ON: When tilt and telescopic switch long operation performed | - |
The value of each Data List item changes in accordance with the operation of the switch.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the I43 multiplex tilt and telescopic ECU connector.
Disconnect the I46 tilt and telescopic switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I43,I46)Location & Routingewd_type=routing;type=c,c;code=I43,I46 |
||
| I43-5 (VC) - I46-1 (VC) | Always | Below 1 Ω |
| I43-18 (MSW) - I46-3 (MSW) | Always | Below 1 Ω |
| I43-5 (VC) or I46-1 (VC) - Body ground | Always | 10 kΩ or higher |
| I43-18 (MSW) or I46-3 (MSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I43 multiplex tilt and telescopic ECU connector.
| *a | Component with harness connected (Multiplex Tilt and Telescopic ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I43)Location & Routingewd_type=routing;type=c;code=I43 |
||
| I43-5 (VC) - I43-18 (MSW) | Ignition switch ON | 4.9 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereSteering>STEERING COLUMN>TILT AND TELESCOPIC MANUAL SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG