CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND POWER DISTRIBUTION BOX ASSEMBLY
| *1 | Power Distribution Box Assembly | *2 | Main body ECU (multiplex network body ECU) |
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Connect the power distribution box assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A-13 (GND1) - Body ground | Ground | Always | Below 1 Ω |
| A-26 (BECU) - Body ground | Battery power supply | Always | 11 to 14 V |
| A-27 (IGR) - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | ||
| A-2 (FLCY) - Body ground | Front door courtesy light switch assembly LH input signal | Front door LH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| A-4 (FRCY) - Body ground | Front door courtesy light switch assembly RH input signal | Front door RH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| A-6 (LCTY) - Body ground | Rear door courtesy light switch assembly LH input signal | Rear door LH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| A-1 (RCTY) - Body ground | Rear door courtesy light switch assembly RH input signal | Rear door RH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| A-19 (BCTY) - Body ground | Back door courtesy light switch signal | Back door closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| I3-27 (HCTY) - Body ground | Engine hood courtesy switch input signal | Engine hood open (OFF) → closed (ON) | 10 kΩ or higher → Below 1 Ω |
Install the main body ECU (multiplex network body ECU) to the power distribution box assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I2-11 (LIN4) - Body ground | LIN communication line | LIN communication line | Pulse generation |
| I3-9 (LSFL) - Body ground | Front door LH unlock detection switch input signal | Front door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed and front door LH locked | Pulse generation | ||
| I3-3 (LSFR) - Body ground | Front door RH unlock detection switch input signal | Front door RH unlocked | Below 1 V |
| Ignition switch off, all doors closed and front door RH locked | Pulse generation | ||
| I3-10 (LSWL) - Body ground | Rear door LH unlock detection switch input signal | Rear door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed and rear door LH locked | Pulse generation | ||
| I2-23 (LSWR) - Body ground | Rear door RH unlock detection switch input signal | Rear door RH unlocked | Below 1 V |
| Ignition switch off, all doors closed and rear door RH locked | Pulse generation | ||
| I2-16 (SSCL) - Body ground*2 | Theft warning siren assembly drive | Theft warning siren assembly sounding (Theft deterrent system is in alarm sounding state) | Pulse generation (Below 1 V ←→ 11 to 14 V) |
| I2-20 (SSW1) - Body ground*3 | Intrusion sensor cancel switch signal | Intrusion sensor cancel switch on | Below 1 V |
| Intrusion sensor cancel switch off | Pulse generation | ||
| I2-8 (GPBS) - Body ground*3 | Glass breakage sensor signal | Glass breakage sensor normal | Below 2 V |
| Glass breakage sensor malfunctioning | 4.5 to 14 V | ||
| 5E-4 (SH) - Body ground*1 | Security horn drive | Security horn sounding (Theft deterrent system is in alarm sounding state) | Pulse generation (Below 1 V ←→ 11 to 14 V) |
| 5E-11 (HORN) - Body ground | Vehicle horn drive | Vehicle horns sounding (Theft deterrent system is in alarm sounding state) | Pulse generation (Below 1 V ←→ 11 to 14 V) |
*1: w/ Security Horn Assembly
*2: w/o Security Horn Assembly
*3: w/ Intrusion Sensor Cancel Switch
CHECK COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)