Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0468612 THEFT DETERRENT SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  B276F87  Intrusion Sensor 1 Missing Message  B277187  Inclination Sensor Missing Message  


DESCRIPTION

This DTC is stored when LIN communication between the main body ECU (multiplex network body ECU) and theft warning ultrasonic and tilt sensor stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B276F87 Intrusion Sensor 1 Missing Message No communication between the main body ECU (multiplex network body ECU) and intrusion sensor for 10 seconds or more.
·

Map light assembly

·

Theft warning ultrasonic and tilt sensor

·

Harness or connector


Main Body B
B277187 Inclination Sensor Missing Message No communication between the main body ECU (multiplex network body ECU) and inclination sensor for 10 seconds or more.
·

Theft warning ultrasonic and tilt sensor


Main Body B

WIRING DIAGRAM

B610256E02
2.365,3.583 4.01,3.813 1.646,0.229 10 false Map Light Assembly 0.75,5.094 2.438,5.333 1.688,0.24 10 false : LIN Communication Line 3.698,5.188 7.063,5.385 3.365,0.198 10 false d23 3.708,5.333 4.76,5.552 1.052,0.219 10 false Rain Sensor* 4.396,4.76 5.469,5.125 1.073,0.365 10 false MPX 4.813,4.594 5.885,4.958 1.073,0.365 10 false 3 6.031,2.708 7.104,3.073 1.073,0.365 10 false LIN4 5.771,2.573 6.844,2.938 1.073,0.365 10 false 11 4.406,2.563 4.74,2.75 0.333,0.188 10 false LIN1 4.844,2.542 5.083,2.729 0.24,0.188 10 false 13 4.427,1.792 5.5,2.156 1.073,0.365 10 false +B2 2.031,1.24 3.823,1.594 1.792,0.354 10 false Theft Warning Ultrasonic and Tilt Sensor 1.396,2.729 1.906,2.958 0.51,0.229 10 false GND5 1.063,2.635 1.271,2.854 0.208,0.219 10 false 24 1.688,0.292 2.5,0.729 0.813,0.438 10 false from Battery 3.427,0.479 5.042,0.885 1.615,0.406 10 false ECU-DCC NO.1 5.76,3.406 6.115,3.583 0.354,0.177 10 false I2 5.75,3.583 6.948,4.115 1.198,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 4.844,1.708 5.083,1.896 0.24,0.188 10 false 12 4.854,1.906 5.198,2.083 0.344,0.177 10 false d1 4.844,2.74 5.188,2.917 0.344,0.177 10 false d2 1.073,2.854 1.417,3.031 0.344,0.177 10 false d1 0.698,5.417 2.385,5.656 1.688,0.24 10 false *: w/ Rain Sensor 5.26,3.688 5.448,3.896 0.188,0.208 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

If DTC B276C88 is output, troubleshoot for DTC B276C88 first.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>B276C88



PROCEDURE

1.CHECK FOR DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

b.

Turn the ignition switch to ON and wait for at least 10 seconds.


Procedure1

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B276F87 is output A
DTCs B276F87 and B277187 are output
DTC B277187 is output B


Post-procedure1

d.

None



A

2.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - BATTERY AND BODY GROUND)

B

REPLACE THEFT WARNING ULTRASONIC AND TILT SENSOR

2.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the d1 map light assembly connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(d1)Location & Routing

Click Connector(d1)Body>No. 1 Roof Wire>Map Light Assembly (Front)

d1-12 (+B2) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d1)Location & Routing

Click Connector(d1)Body>No. 1 Roof Wire>Map Light Assembly (Front)

d1-24 (GND5) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY)

Pre-procedure1

a.

Disconnect the I2 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the d2 map light assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I2,d2)Location & Routing

Click Connector(I2)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

Click Connector(d2)Body>No. 1 Roof Wire>Map Light Assembly (Front)

I2-11 (LIN4) - d2-13 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

4.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY

Pre-procedure1

a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL

B610521C03
0.5,0.292 1.042,0.5 0.542,0.208 2.792,0.292 3.333,0.5 0.542,0.208 5.688,0.323 6.229,0.531 0.542,0.208 0.406,0.594 0.583,0.594 0.583,0.594 0.635,0.917 true 0.438,1.385 0.615,1.385 0.615,1.385 0.823,0.99 true 1.125,1.385 1,1.385 1,1.385 0.917,0.979 true 2.146,1.49 2.021,1.49 2.021,1.49 1.938,1.083 true 4.271,1.458 4.146,1.458 4.146,1.458 4.063,1.052 true 5.865,1.448 5.74,1.448 5.74,1.448 5.656,1.042 true 0.75,0.333 1.094,0.563 0.344,0.229 10 false A 3,0.333 3.344,0.563 0.344,0.229 10 false B 5.906,0.354 6.25,0.583 0.344,0.229 10 false C 0.125,0.531 0.521,0.76 0.396,0.229 10 false +B2 0.135,1.333 0.531,1.563 0.396,0.229 10 false LIN1 1.198,1.323 1.594,1.552 0.396,0.229 10 false GND 2.188,1.438 2.583,1.667 0.396,0.229 10 false GND 4.323,1.396 4.719,1.625 0.396,0.229 10 false +B2 5.917,1.385 6.313,1.615 0.396,0.229 10 false LIN1 0.115,0.063 0.51,0.292 0.396,0.229 10 false *a
*a Component without harness connected
(Map Light Assembly)
- -



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (GND) - B-24 (GND) Always Below 1 Ω
A-2 (LIN1) - C-13 (LIN1) Always Below 1 Ω
A-4 (+B2) - B-12 (+B2) Always Below 1 Ω
A-1 (GND) or B-24 (GND) - Other terminals and body ground Always 10 kΩ or higher
A-4 (+B2) or B-12 (+B2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE THEFT WARNING ULTRASONIC AND TILT SENSOR

NG

REPLACE MAP LIGHT ASSEMBLY