Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0468612 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine hood courtesy switch is installed together with the hood lock. This switch turns on when the engine hood is closed and turns off when the engine hood is opened.

WIRING DIAGRAM

B472053E62
5.417,2.063 7.083,2.438 1.667,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 0.823,1.542 2.729,1.927 1.906,0.385 10 false Hood Lock Assembly (Engine Hood Courtesy Switch) 5.844,1.01 6.281,1.24 0.438,0.229 10 false HCTY 5.583,1.021 6.021,1.25 0.438,0.229 10 false 27 2.021,1.01 2.458,1.24 0.438,0.229 10 false 2 0.969,1.01 1.406,1.24 0.438,0.229 10 false 1 5.417,1.896 5.854,2.125 0.438,0.229 10 false I3 0.833,1.396 1.271,1.625 0.438,0.229 10 false B36 6.26,0.698 6.698,0.927 0.438,0.229 10 false +B 1.823,1.01 2.26,1.24 0.438,0.229 10 false + 1.146,1.021 1.583,1.25 0.438,0.229 10 false E

CAUTION / NOTICE / HINT

NOTICE:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS (HOOD COURTESY SWITCH STATUS)
a.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Hood Courtesy Switch Status Engine hood courtesy switch ON or OFF ON: Engine hood open
OFF: Engine hood closed
-
Body Electrical > Main Body > Data List
Tester Display
Hood Courtesy Switch Status
50003 449 37
OK:

The indicator on the GTS switches between ON and OFF in accordance with the hood lock assembly (engine hood courtesy switch) status.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (HOOD LOCK ASSEMBLY [ENGINE HOOD COURTESY SWITCH] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (HOOD LOCK ASSEMBLY [ENGINE HOOD COURTESY SWITCH] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the B36 hood lock assembly (engine hood courtesy switch) connector.


b.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B36,I3)Location & Routing

Click Connector(B36)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Hood Courtesy Switch (Hood Lock Assembly)

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

B36-1 (+) - I3-27 (HCTY) Always Below 1 Ω
B36-2 (E) - Body ground Always Below 1 Ω
B36-1 (+) or I3-27 (HCTY) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)

OK

NG

REPLACE HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)