Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0468612 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Cancel Switch Circuit  


DESCRIPTION

When the intrusion sensor cancel switch on the map light assembly is pressed, the sensor off signal is sent to the main body ECU (multiplex network body ECU) which causes the theft warning ultrasonic and tilt sensor to stop operating.

WIRING DIAGRAM

B612320E01
5.969,0.292 6.281,0.49 0.313,0.198 10 false +B 5.271,0.76 5.885,0.958 0.615,0.198 10 false SSW1 1.5,0.646 1.76,0.854 0.26,0.208 10 false 24 3.896,0.667 4.198,0.854 0.302,0.188 10 false 11 4.99,0.74 5.292,0.927 0.302,0.188 10 false 20 4.969,1.677 5.396,1.865 0.427,0.188 10 false I2 3.906,0.865 4.25,1.052 0.344,0.188 10 false d2 2.146,1.448 4.896,1.646 2.75,0.198 10 false Map Light Assembly 4.958,1.844 6.615,2.25 1.656,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 1.802,0.74 2.396,0.979 0.594,0.24 10 false GND5 3.385,0.74 3.823,0.938 0.438,0.198 10 false SOFF 1.823,1 3.802,1.24 1.979,0.24 10 false Intrusion Sensor Cancel Switch 1.5,0.854 1.844,1.042 0.344,0.188 10 false d1

CAUTION / NOTICE / HINT

NOTICE:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS (INTRUSION SENSOR CANCEL SWITCH)
a.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Cancel Switch Intrusion sensor cancel switch ON or OFF ON: Intrusion sensor cancel switch on
OFF: Intrusion sensor cancel switch off
-
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sensor Cancel Switch
50003 449 98
OK:

The indicator on the GTS switches between ON and OFF in accordance with the intrusion sensor cancel switch status.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the I2 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the d1 and d2 map light assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I2,d2,d1)Location & Routing

Click Connector(I2)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

Click Connector(d2)Body>No. 1 Roof Wire>Map Light Assembly (Front)

Click Connector(d1)Body>No. 1 Roof Wire>Map Light Assembly (Front)

I2-20 (SSW1) - d2-11 (SOFF) Always Below 1 Ω
d1-24 (GND5) - Body ground Always Below 1 Ω
I2-20 (SSW1) or d2-11 (SOFF) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)
a.

Remove the map light assembly (intrusion sensor cancel switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL

B610630C01
1.958,0.302 2.5,0.51 0.542,0.208 5.042,0.271 5.583,0.479 0.542,0.208 1.656,1.521 1.344,1.521 1.344,1.521 1.094,1.094 true 5.531,1.5 5.406,1.5 5.406,1.5 5.323,1.094 true 2.188,0.333 2.531,0.563 0.344,0.229 10 false A 5.281,0.313 5.625,0.542 0.344,0.229 10 false B 1.708,1.448 2.292,1.677 0.583,0.229 10 false GND5 5.604,1.448 6,1.677 0.396,0.229 10 false SOFF 0.198,0.135 0.51,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Map Light Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-11 (SOFF) - A-24 (GND5) Intrusion sensor cancel switch not pressed 10 kΩ or higher
B-11 (SOFF) - A-24 (GND5) Intrusion sensor cancel switch pressed Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)