Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0468612 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Circuit  


DESCRIPTION

If no warnings operate or the system can be set even though the conditions to set the system are not met, the main body ECU (multiplex network body ECU) cannot perform recognition due to a cutoff of the ON signal from the courtesy light switch from the doors, engine hood or back door, or some other problem.

If the automatic alarm operates when it should not operate, it may be due to a false detection by the intrusion sensor (theft warning ultrasonic and tilt sensor) or due to the ON signal being input when there is a short circuit in the courtesy light switch of the doors, engine hood or back door, or some other problem which would cause this to happen.

HINT:

In the following situations, the intrusion sensor (theft warning ultrasonic and tilt sensor) may operate and cause the automatic alarm system to operate even when the sensor is normal.

·

The driver steps away from the vehicle while other people, pets, etc. are in the vehicle.

·

There are things which move easily inside the vehicle, such as things hanging inside the vehicle or clothing hanging from the coat hooks.

·

Any window is open.

·

The vehicle is parked in a place with a lot of vibration or noise such as a parking garage.

·

The vehicle is being washed using a high-pressure spray gun or an automatic car washing machine.

·

The vehicle is continuously being struck or is vibrating due to hail or lightning.

·

The vehicle is continuously being subjected to impacts or is vibrating when snow or ice is being removed from the vehicle.

·

A frost prevention sheet which has an aluminum film is moved by wind, etc.



WIRING DIAGRAM

B610256E02
2.365,3.583 4.01,3.813 1.646,0.229 10 false Map Light Assembly 0.75,5.094 2.438,5.333 1.688,0.24 10 false : LIN Communication Line 3.698,5.188 7.063,5.385 3.365,0.198 10 false d23 3.708,5.333 4.76,5.552 1.052,0.219 10 false Rain Sensor* 4.396,4.76 5.469,5.125 1.073,0.365 10 false MPX 4.813,4.594 5.885,4.958 1.073,0.365 10 false 3 6.031,2.708 7.104,3.073 1.073,0.365 10 false LIN4 5.771,2.573 6.844,2.938 1.073,0.365 10 false 11 4.406,2.563 4.74,2.75 0.333,0.188 10 false LIN1 4.844,2.542 5.083,2.729 0.24,0.188 10 false 13 4.427,1.792 5.5,2.156 1.073,0.365 10 false +B2 2.031,1.24 3.823,1.594 1.792,0.354 10 false Theft Warning Ultrasonic and Tilt Sensor 1.396,2.729 1.906,2.958 0.51,0.229 10 false GND5 1.063,2.635 1.271,2.854 0.208,0.219 10 false 24 1.688,0.292 2.5,0.729 0.813,0.438 10 false from Battery 3.427,0.479 5.042,0.885 1.615,0.406 10 false ECU-DCC NO.1 5.76,3.406 6.115,3.583 0.354,0.177 10 false I2 5.75,3.583 6.948,4.115 1.198,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 4.844,1.708 5.083,1.896 0.24,0.188 10 false 12 4.854,1.906 5.198,2.083 0.344,0.177 10 false d1 4.844,2.74 5.188,2.917 0.344,0.177 10 false d2 1.073,2.854 1.417,3.031 0.344,0.177 10 false d1 0.698,5.417 2.385,5.656 1.688,0.24 10 false *: w/ Rain Sensor 5.26,3.688 5.448,3.896 0.188,0.208 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS (COMMUNICATION INTRUSION SENSOR 1)
a.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Communication Intrusion Sensor 1 Theft warning ultrasonic and tilt sensor connecting ON or OFF ON: Theft warning ultrasonic and tilt sensor connected
OFF: Theft warning ultrasonic and tilt sensor not connected
-
Body Electrical > Main Body > Data List
Tester Display
Communication Intrusion Sensor 1
50003 449 1655
OK:

"ON" appears on GTS screen.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - MAP LIGHT ASSEMBLY)
a.

Disconnect the I2 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the d2 map light assembly connector.


c.

Disconnect the d23 rain sensor connector.*

*: w/ Rain Sensor



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I2,d2)Location & Routing

Click Connector(I2)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

Click Connector(d2)Body>No. 1 Roof Wire>Map Light Assembly (Front)

I2-11 (LIN4) - d2-13 (LIN1) Always Below 1 Ω
I2-11 (LIN4) or d2-13 (LIN1) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL

B610521C02
0.5,0.292 1.042,0.5 0.542,0.208 2.792,0.292 3.333,0.5 0.542,0.208 5.688,0.323 6.229,0.531 0.542,0.208 0.406,0.594 0.583,0.594 0.583,0.594 0.635,0.917 true 0.438,1.385 0.615,1.385 0.615,1.385 0.823,0.99 true 1.125,1.385 1,1.385 1,1.385 0.917,0.979 true 2.146,1.49 2.021,1.49 2.021,1.49 1.938,1.083 true 4.271,1.458 4.146,1.458 4.146,1.458 4.063,1.052 true 5.865,1.448 5.74,1.448 5.74,1.448 5.656,1.042 true 0.75,0.333 1.094,0.563 0.344,0.229 10 false A 3,0.333 3.344,0.563 0.344,0.229 10 false B 5.906,0.354 6.25,0.583 0.344,0.229 10 false C 0.125,0.531 0.521,0.76 0.396,0.229 10 false +B2 0.135,1.333 0.531,1.563 0.396,0.229 10 false LIN1 1.198,1.323 1.594,1.552 0.396,0.229 10 false GND 2.188,1.438 2.844,1.708 0.656,0.271 10 false GND5 4.323,1.396 4.719,1.625 0.396,0.229 10 false +B2 5.917,1.385 6.313,1.615 0.396,0.229 10 false LIN1 0.104,0.063 0.5,0.292 0.396,0.229 10 false *a
*a Component with harness connected
(Map Light Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (GND) - B-24 (GND5) Always Below 1 Ω
A-2 (LIN1) - C-13 (LIN1) Always Below 1 Ω
A-4 (+B2) - B-12 (+B2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC AND TILT SENSOR)

NG

REPLACE MAP LIGHT ASSEMBLY

4.REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC AND TILT SENSOR)
a.

Replace the intrusion sensor (Theft warning ultrasonic and tilt sensor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>INTRUSION SENSOR>REMOVAL


b.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition
Communication Intrusion Sensor 1 Theft warning ultrasonic and tilt sensor connecting ON or OFF ON: Theft warning ultrasonic and tilt sensor connected
OFF: Theft warning ultrasonic and tilt sensor not connected
Body Electrical > Main Body > Data List
Tester Display
Communication Intrusion Sensor 1
50003 449 1655
OK:

"ON" appears on GTS screen.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG