Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM38G0E _58 Vehicle Interior _100886 DOOR LOCK _0468613 POWER DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  B124300  Impact Detection Sensor Circuit Malfunction  


DESCRIPTION

If the collision door lock release function does not operate normally, or an open or short in the GSW input circuit of the main body ECU (multiplex network body ECU) is detected, DTC B124300 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B124300 Impact Detection Sensor Circuit Malfunction A malfunction occurs in the GSW input circuit of the main body ECU (multiplex network body ECU).
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Airbag ECU assembly

·

Harness or connector


Main Body A

WIRING DIAGRAM

B581847E21
1.25,0.938 1.708,1.135 0.458,0.198 10 false GSW 1.667,0.833 1.979,1.031 0.313,0.198 10 false 25 0.583,1.802 1.042,2 0.458,0.198 10 false I24 0.583,1.969 3.156,2.385 2.573,0.417 10 false Airbag ECU Assembly 5.646,0.938 6.104,1.135 0.458,0.198 10 false GSW 4.365,0.823 4.677,1.021 0.313,0.198 10 false 43 5.406,0.823 5.719,1.021 0.313,0.198 10 false 20 4.156,1.281 4.469,1.479 0.313,0.198 10 false 5C 4.146,1.427 5.563,1.813 1.417,0.385 10 false Power Distribution Box Assembly 5.344,1.802 5.656,2 0.313,0.198 10 false A 5.344,1.979 7,2.531 1.656,0.552 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

When DTC B124300 is output, the collision door lock release, shift-linked automatic door lock/unlock and speed-sensitive automatic door lock functions are prohibited.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

The battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449
OK:

DTC B124300 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

Turning the ignition switch to ON with the airbag ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Disconnect the airbag ECU assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I24)Location & Routing

Click Connector(I24)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Airbag with ECU Sensor Assembly

I24-25 (GSW) - Body ground Ignition switch ON 4.3 to 5.5 V



Result:
Proceed to
OK
NG


Post-procedure1

e.

None



OK

NG

4.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - AIRBAG ECU ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - AIRBAG ECU ASSEMBLY)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



b.

Disconnect the 5C power distribution box assembly connector.


c.

Disconnect the I24 airbag ECU assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I24)Location & Routing

Click Connector(I24)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Airbag with ECU Sensor Assembly

5C-43 - I24-25 (GSW) Always Below 1 Ω
5C-43 or I24-25 (GSW) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

e.

None



OK

5.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

Pre-procedure1


b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

B575806C03
4.76,0.5 5.135,0.76 0.375,0.26 1.354,0.24 1.729,0.5 0.375,0.26 5.854,1.552 5.708,1.552 5.708,1.552 5.625,1.208 true 1.469,0.302 1.781,0.5 0.313,0.198 10 false 5C 4.906,0.563 5.219,0.76 0.313,0.198 10 false A 5.927,1.458 6.458,1.646 0.531,0.188 10 false GSW 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Power Distribution Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A-20 (GSW) - 5C-43 Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG