Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM38G0E _58 Vehicle Interior _100886 DOOR LOCK _0468613 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Only Back Door cannot be Opened  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives signals from the back door opener switch assembly. Then, the main body ECU (multiplex network body ECU) activates the back door lock motor.

WIRING DIAGRAM

B575805E06
5.354,0.604 5.813,0.802 0.458,0.198 10 false TR+ 3.875,1.594 4.844,1.802 0.969,0.208 10 false DOOR BACK 2.333,0.771 2.792,0.969 0.458,0.198 10 false 5H 2.375,0.573 2.833,0.771 0.458,0.198 10 false 1 5.094,0.656 5.552,0.854 0.458,0.198 10 false 5 2.344,1.833 2.802,2.031 0.458,0.198 10 false 5C 2.323,1.073 2.781,1.271 0.458,0.198 10 false 36 0.823,0.708 2.521,0.958 1.698,0.25 10 false from Battery 3.083,3.458 3.542,3.656 0.458,0.198 10 false 5F 3.115,3.26 3.573,3.458 0.458,0.198 10 false 2 1.99,2.844 2.531,3.031 0.542,0.188 10 false ACT+ 2.458,2.844 3,3.031 0.542,0.188 10 false 1 2.25,3.375 2.792,3.563 0.542,0.188 10 false + 2.469,3.365 3.01,3.552 0.542,0.188 10 false 3 0.885,2.813 1.427,3 0.542,0.188 10 false ACT- 0.635,2.823 1.177,3.01 0.542,0.188 10 false 2 0.813,3.854 1.354,4.042 0.542,0.188 10 false g4 0.802,4.042 2.771,4.438 1.969,0.396 10 false Back Door Lock with Courtesy Light Switch Assembly 3.135,3.969 5.24,4.302 2.104,0.333 10 false Power Distribution Box Assembly 0.896,5.656 2.729,6.01 1.833,0.354 10 false Certification ECU (Smart Key ECU Assembly) 4.938,6.063 7.156,6.469 2.219,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 0.74,7.135 2.448,7.344 1.708,0.208 10 false : CAN Communication Line 5.417,3.333 5.875,3.531 0.458,0.198 10 false BCTY 5.083,3.354 5.542,3.552 0.458,0.198 10 false 19 3.073,2.938 3.531,3.135 0.458,0.198 10 false 5F 3.073,2.74 3.531,2.938 0.458,0.198 10 false 39 2.354,1.625 2.813,1.823 0.458,0.198 10 false 41 2.333,1.292 2.792,1.49 0.458,0.198 10 false 5B 2.771,0.927 3.74,1.135 0.969,0.208 10 false DOOR BACK 4.969,5.906 7.156,6.313 2.188,0.406 10 false A 6.25,2.719 6.708,2.917 0.458,0.198 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the vehicle ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The power door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

The battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (Trunk Lid / Back Door Open)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Trunk Lid / Back Door Open Back door lock motor OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Trunk Lid / Back Door Open
50004 449 15
OK:

The back door lock with courtesy light switch assembly unlatches when ON is selected.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY
2.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)
a.

Disconnect the g4 back door lock with courtesy light switch assembly connector.


b.

Disconnect the 5F power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g4)Location & Routing

Click Connector(g4)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

g4-1 (ACT+) - 5F-39 Always Below 1 Ω
g4-3 (+) - 5F-2 Always Below 1 Ω
g4-2 (ACT-) - Body ground Always Below 1 Ω
g4-1 (ACT+) or 5F-39 - Other terminals and body ground Always 10 kΩ or higher
g4-3 (+) or 5F-2 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E436390C05
1.302,0.219 1.802,0.469 0.5,0.25 5,0.5 5.5,0.75 0.5,0.25 6.365,1.396 6.115,1.396 6.115,1.396 5.865,1 true 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 5.198,0.563 5.542,0.792 0.344,0.229 10 false A 6.427,1.333 6.823,1.563 0.396,0.229 10 false BCTY 1.469,0.281 1.813,0.51 0.344,0.229 10 false 5F
*a Component without harness connected
(Power Distribution Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A-19 (BCTY) -5F-2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - BATTERY AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the power distribution box assembly connectors.

B575804C02
0.635,0.375 0.979,0.656 0.344,0.281 2.76,0.396 3.104,0.677 0.344,0.281 5.635,0.406 5.979,0.688 0.344,0.281 0.74,0.458 1.052,0.656 0.313,0.198 10 false 5H 2.854,0.479 3.167,0.698 0.313,0.219 10 false 5B 5.729,0.5 6.042,0.719 0.313,0.219 10 false 5C 0.198,0.135 0.51,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5H-1 - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5B-36 - Body ground Always Below 1 Ω
5C-41 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK POWER DISTRIBUTION BOX ASSEMBLY (DOOR BACK RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POWER DISTRIBUTION BOX ASSEMBLY (DOOR BACK RELAY)

b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

B611601C03
1.667,0.26 2.167,0.583 0.5,0.323 5.083,0.26 5.583,0.583 0.5,0.323 1.667,2.333 2.167,2.656 0.5,0.323 5.083,2.083 5.583,2.406 0.5,0.323 1.427,3.479 1.25,3.479 1.25,3.479 1.073,3.031 true 1.854,0.333 2.167,0.531 0.313,0.198 10 false 5F 5.25,0.333 5.563,0.531 0.313,0.198 10 false 5B 1.885,2.417 2.198,2.615 0.313,0.198 10 false A 5.25,2.167 5.563,2.365 0.313,0.198 10 false 5H 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 1.49,3.385 2.052,3.635 0.563,0.25 10 false TR+
*a Component without harness connected
(Power Distribution Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
5F-39 - 5B-36 Battery voltage applied to terminals 5H-1 and A-5 (TR+) 10 kΩ or higher
5F-39 - 5B-36 Battery voltage not applied to terminals 5H-1 and A-5 (TR+) Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5F-39 - Battery negative (-) terminal Battery voltage applied to terminals 5H-1 and A-5 (TR+) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG