When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn to sound at intervals of 0.4 seconds.
Inspect the fuses for circuits related to this system before performing the following procedure.
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Security Horn | Security horn assembly | ON or OFF | - |
| Tester Display |
|---|
| Security Horn |
The security horn assembly sounds and stops correctly when operated through the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY HORN ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected (Security Warning Relay (S-HORN)) |
Remove the security warning relay (S-HORN).
Measure the resistance according to the value(s) in the table below
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Security warning relay (S-HORN) terminal 3 - Security warning relay (S-HORN) terminal 5 | Battery voltage is applied between security warning relay (S-HORN) terminals 2 - 1 | Below 1 Ω |
| Security warning relay (S-HORN) terminal 3 - Security warning relay (S-HORN) terminal 5 | Battery voltage is not applied between security warning relay (S-HORN) terminals 2 - 1 | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the main body ECU (multiplex network body ECU).
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Connect the power distribution box assembly connectors.
Remove the security warning relay (S-HORN).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Security warning relay (S-HORN) terminal 2 - A-24 (SH) | Always | Below 1 Ω |
| Security warning relay (S-HORN) terminal 2 or A-24 (SH) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Security Warning Relay [S-HORN]) |
Remove the security warning relay (S-HORN).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Security warning relay (S-HORN) terminal 1 - Body ground | Always | 11 to 14 V |
| Security warning relay (S-HORN) terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the security warning relay (S-HORN).
Disconnect the B34 security horn assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B34)Location & Routingewd_type=routing;type=c;code=B34 |
||
| Security warning relay (S-HORN) terminal 3 - B34-1 | Always | Below 1 Ω |
| Security warning relay (S-HORN) terminal 3 or B34-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the 5E power distribution box assembly connector.
Remove the security warning relay (S-HORN).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Security warning relay (S-HORN) terminal 2 - 5E-4 | Always | Below 1 Ω |
| Security warning relay (S-HORN) terminal 2 or 5E-4 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG