Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM38G0E _58 Vehicle Interior _100886 DOOR LOCK _0468613 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the door control switch assembly. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

B577611E03
5.375,2.74 7.021,3.323 1.646,0.583 10 false Main Body ECU (Multiplex Network Body ECU) 1.177,1.875 3.083,2.521 1.906,0.646 10 false Door Control Switch Assembly 5.51,0.542 7.156,1.125 1.646,0.583 10 false 6 5.51,1.188 7.156,1.771 1.646,0.583 10 false 7 1.219,1.729 2.865,2.313 1.646,0.583 10 false M3 5.74,0.573 6.26,1.219 0.521,0.646 10 false L1 5.74,1.219 6.26,1.865 0.521,0.646 10 false UL1 6.01,0.281 6.531,0.927 0.521,0.646 10 false +B 6.031,0.958 6.552,1.604 0.521,0.646 10 false +B 2.802,0.552 4.448,1.135 1.646,0.583 10 false 4 2.823,1.208 4.469,1.792 1.646,0.583 10 false 2 1.115,1.219 2.76,1.802 1.646,0.583 10 false 5 1.281,1.219 1.802,1.865 0.521,0.646 10 false E 1.833,0.76 2.354,1.406 0.521,0.646 10 false LOCK 1.75,1.438 2.583,2.073 0.833,0.635 10 false UNLOCK 2.615,0.563 3.135,1.208 0.521,0.646 10 false L 2.552,1.219 3.073,1.865 0.521,0.646 10 false UL 5.375,2.583 5.896,3.229 0.521,0.646 10 false I2

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

The battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.READ VALUE USING GTS (Manual Door Lock Switch (D/P Door), Manual Door Unlock Switch (D/P Door))
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Manual Door Lock Switch (D/P Door) Front passenger door control switch lock signal OFF or ON OFF: Lock side of front passenger door control switch not pushed
ON: Lock side of front passenger door control switch pushed
-
Manual Door Unlock Switch (D/P Door) Front passenger door control switch unlock signal OFF or ON OFF: Unlock side of front passenger door control switch not pushed
ON: Unlock side of front passenger door control switch pushed
-
Body Electrical > Main Body > Data List
Tester Display
Manual Door Lock Switch (D/P Door)
Manual Door Unlock Switch (D/P Door)
50003 449 10,12
OK:

The GTS indicates ON or OFF according to the switch operation shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT DOOR CONTROL SWITCH ASSEMBLY
2.INSPECT DOOR CONTROL SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the M3 door control switch assembly connector.


b.

Disconnect the I2 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M3,I2)Location & Routing

Click Connector(M3)Body>Front Door Wire RH>Door Control Switch Assembly

Click Connector(I2)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

M3-4 (L) - I2-6 (L1) Always Below 1 Ω
M3-2 (UL) - I2-7 (UL1) Always Below 1 Ω
M3-5 (E) - Body Ground Always Below 1 Ω
M3-4 (L) or I2-6 (L1) - Other terminals and body ground Always 10 kΩ or higher
M3-2 (UL) or I2-7 (UL1) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR