Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER
RM38G0E _53 Suspension _100922 REAR SUSPENSION _0468691 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C458809N01
6.646,5.115 6.479,5.115 6.479,5.115 6.313,4.823 true 4.833,2.333 4.75,2.333 4.75,2.333 4.583,2.667 true 2.615,3.979 2.948,3.979 true 2.51,3.771 2.844,3.771 true 3.281,1.052 3.615,1.052 true 0.51,2.844 0.844,2.844 true 2.917,4.479 3.25,4.479 true 2.083,0.646 2.417,0.646 true 6.51,0.229 6.844,0.229 true 2.396,3.594 2.729,3.594 true 3.698,0.906 3.979,1.26 0.281,0.354 18 false 2 6.323,0.115 6.656,0.448 0.333,0.333 18 false 3 6.729,4.938 7.073,5.271 0.344,0.333 18 false 1 4.906,2.198 5.24,2.531 0.333,0.333 18 false 4 2.927,3.698 3.24,3.896 0.313,0.198 10 false *1 3.01,3.906 3.323,4.104 0.313,0.198 10 false *2 3.625,4.354 3.958,4.688 0.333,0.333 18 false 6 0.302,2.708 0.635,3.042 0.333,0.333 18 false 5 2.51,0.51 2.854,0.844 0.344,0.333 18 false 1 2.792,3.49 3.167,3.688 0.375,0.198 10 false ●*3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR WHEEL - - - -
2 REAR AXLE BREATHER HOSE SUB-ASSEMBLY 42306 - - -
3 SUPPORT REAR AXLE HOUSING ASSEMBLY - (Click here) - -
4 REAR LATERAL CONTROL ROD ASSEMBLY 48740 - - -
5 REAR SHOCK ABSORBER ASSEMBLY RH 48530 - - -
6 REAR SHOCK ABSORBER ASSEMBLY LH 48540 (Click here) - -

*1 REAR NO. 1 SHOCK ABSORBER CUSHION *2 REAR NO. 2 SHOCK ABSORBER CUSHION
*3 LOCK NUT - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear shock absorber removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Suspension, tires, etc. Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)


HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 42306 2.DISCONNECT REAR AXLE BREATHER HOSE SUB-ASSEMBLY

a.
C456103


Hide 3.SUPPORT REAR AXLE HOUSING ASSEMBLY

a.
C456104C01
4.385,1.031 5.083,0.583 5.083,0.583 5.25,0.583 true 4.667,1.583 4.5,1.583 4.5,1.583 4.333,1.5 true 5.313,0.479 5.625,0.677 0.313,0.198 10 false *a 4.75,1.5 5.063,1.698 0.313,0.198 10 false *b 0.563,0.073 1,0.385 0.438,0.313 18 false i
*a Wooden Block *b Jack


i.

Using a jack and wooden block, support the rear axle housing assembly.

NOTICE:
·

When jacking up the rear axle housing assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.





Hide 48740 4.DISCONNECT REAR LATERAL CONTROL ROD ASSEMBLY

a.
C456105


Hide 48530 5.DISCONNECT REAR SHOCK ABSORBER ASSEMBLY RH

a.
C457419


Hide 48540 6.REMOVE REAR SHOCK ABSORBER ASSEMBLY LH

a.
C456106C01
0.479,0.031 0.781,0.302 0.302,0.271 18 true i 4.063,0.01 4.365,0.281 0.302,0.271 18 true ii 0.365,2.021 0.688,2.344 0.323,0.323 18 true iii 3.896,2.042 4.167,2.375 0.271,0.333 18 true iv 0.104,0.063 0.417,0.26 0.313,0.198 10 false *A
*A w/ AVS - -


i.

w/ AVS:

Disconnect the connector.


ii.

Remove the bolt on the lower side of the rear shock absorber assembly LH.


iii.

Remove the nut, rear No. 1 shock absorber cushion and rear shock absorber assembly LH as shown in the illustration.


iv.

Remove the rear No. 2 shock absorber cushion from the rear shock absorber assembly LH.