Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE
RM38G0E _52 Drivetrain _100436 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0468718 TRANSMISSION CONTROL CABLE A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C456460N02
1.75,3.302 2.417,3.469 0.667,0.167 4.417,3.333 3.833,3.333 3.833,3.333 3.833,2.927 false 3.51,2.521 3.885,2.521 false 2.417,3.385 2.917,3.385 false 4.875,3.177 5.208,3.594 0.333,0.417 18 false 1 3.333,2.427 3.5,2.594 0.167,0.167 10 false ● 1.813,3.302 2.563,3.469 0.75,0.167 8 false 12 (122, 9)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

C456459N03
5.083,2.25 5.5,2.25 false 6.167,3.458 6.417,3.458 6.417,3.458 6.667,3.042 false 4.917,2.094 5.25,2.51 0.333,0.417 18 false 3 5.969,3.292 6.302,3.708 0.333,0.417 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

2 CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -
3 FLOOR SHIFT LEVER ASSEMBLY - - - -

PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C458209

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.
C456463C01
5,0.333 5.229,0.333 5.229,0.333 5.229,0.583 false 2,2.667 2.333,2.667 true 0.5,0 0.75,0.292 0.25,0.292 18 true i 0.5,2.083 0.75,2.375 0.25,0.292 18 true ii 4.833,0.25 5,0.417 0.167,0.167 10 false *a 4,2.469 4.167,2.635 0.167,0.167 10 false *b 2.333,2.583 2.5,2.75 0.167,0.167 10 true *a
*a Clip *b 45° to 60°
V113147

Install in this Direction - -


i.

Connect the transmission control cable assembly to the transmission control shaft lever RH as shown in the illustration.

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in N.



ii.

Install a new clip to the No. 1 transmission control cable bracket.



Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C456458C01
0.417,0.042 0.75,0.458 0.333,0.417 18 false i 3.979,0.063 4.313,0.479 0.333,0.417 18 false ii 1.854,2.031 2.354,2.448 0.5,0.417 18 false iii
V113147

Install in this Direction - -


i.

Insert the transmission control cable assembly in the floor hole.


ii.

Attach the grommet into the floor hole.

NOTICE:
·

The grommet seal should not be caught or lifted.

·

Do not twist the transmission control cable assembly too much.




iii.

Attach the clamp and connect the wire harness connector holder.