If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.
If power window initialization has not been performed, the auto up and down function will not operate.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION
for LHD:
for RHD:
If the front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) has been replaced with a new one, initialize the power window control system.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION
Check that the "P Window Auto Up" and "P Window Auto Down" power window control system customize settings are "ON" before proceeding with work.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>CUSTOMIZE PARAMETERS
After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally.
If the pulse sensor built into the front power window regulator motor assembly RH is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator switch assembly at the auto up position, and opened manually by pushing down the power window regulator switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>FAIL-SAFE CHART
Using the GTS, read the data for the condition when the power window regulator switch assembly was operated.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P Door P/W Auto SW | Front passenger door power window auto switch signal | OFF or ON | OFF: Front passenger door power window auto switch not being operated ON: Front passenger door power window auto switch being operated |
- |
| Tester Display |
|---|
| P Door P/W Auto SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Initialize the front power window regulator motor assembly RH.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION
Power window system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Initialize the front power window regulator motor assembly LH.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION
Power window system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the N4 power window regulator switch assembly connector.
Disconnect the N6 front power window regulator motor assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(N6,N4)Location & Routingewd_type=routing;type=c,c;code=N6,N4 Click Connector(N6)Body>Front Door Wire LH>Front Power Window Regulator Motor Assembly LHewd_type=component;type=c;code=N6;pinno=4 Click Connector(N4)Body>Front Door Wire LH>Front Power Window Regulator Switch Assembly LHewd_type=component;type=c;code=N4;pinno=8 |
||
| N6-4 (AUTO) - N4-8 (AUTO) | Always | Below 1 Ω |
| N6-4 (AUTO) or N4-8 (AUTO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M5 power window regulator switch assembly connector.
Disconnect the M7 front power window regulator motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(M7,M5)Location & Routingewd_type=routing;type=c,c;code=M7,M5 Click Connector(M7)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RHewd_type=component;type=c;code=M7;pinno=4 Click Connector(M5)Body>Front Door Wire RH>Front Power Window Regulator Switch Assembly RHewd_type=component;type=c;code=M5;pinno=8 |
||
| M7-4 (AUTO) - M5-8 (AUTO) | Always | Below 1 Ω |
| M7-4 (AUTO) or M5-8 (AUTO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG