Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM38G0E _58 Vehicle Interior _100749 LIGHTING (INT) _0468730 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Door Courtesy Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the courtesy light switch.

WIRING DIAGRAM

E463608E01
5.635,2.042 6.25,2.24 0.615,0.198 10 false FRCY 5.615,0.688 6.229,0.885 0.615,0.198 10 false FLCY 6.552,0.427 6.865,0.625 0.313,0.198 10 false +B 6.563,1.792 6.875,1.99 0.313,0.198 10 false +B 6.552,3.156 6.865,3.354 0.313,0.198 10 false +B 6.604,4.542 6.917,4.74 0.313,0.198 10 false +B 4.052,5.323 4.365,5.521 0.313,0.198 10 false 5F 5.448,5.49 7.083,5.885 1.635,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 5.448,5.313 5.76,5.51 0.313,0.198 10 false MB 4.042,0.656 4.354,0.854 0.313,0.198 10 false 3 3.083,0.646 3.396,0.844 0.313,0.198 10 false 1 3.083,2.052 3.396,2.25 0.313,0.198 10 false 1 3.073,3.438 3.385,3.635 0.313,0.198 10 false 1 3.073,4.792 3.385,4.99 0.313,0.198 10 false 1 4.094,5.521 5.25,5.958 1.156,0.438 10 false Power Distribution Box Assembly 4.01,3.427 4.323,3.625 0.313,0.198 10 false 26 4.052,2.083 4.365,2.281 0.313,0.198 10 false 5 4.031,4.813 4.344,5.01 0.313,0.198 10 false 1 5.635,3.417 6.25,3.615 0.615,0.198 10 false LCTY 5.656,4.813 6.271,5.01 0.615,0.198 10 false RCTY 0.865,2.792 3.969,3.49 3.104,0.698 10 false Front Door Courtesy Light Switch Assembly RH 0.792,1.25 2.021,1.542 1.229,0.292 10 false S14*1, S15*2 5.365,2.073 5.677,2.271 0.313,0.198 10 false 4 5.344,0.708 5.656,0.906 0.313,0.198 10 false 2 5.344,3.385 5.656,3.583 0.313,0.198 10 false 6 5.438,4.802 5.75,5 0.313,0.198 10 false 1 0.865,2.604 2.167,3.177 1.302,0.573 10 false Q23 0.802,1.427 3.771,2.115 2.969,0.688 10 false Front Door Courtesy Light Switch Assembly LH 0.969,4.156 3.917,4.875 2.948,0.719 10 false Rear Door Courtesy Light Switch Assembly LH 0.948,3.969 1.26,4.167 0.313,0.198 10 false S16 0.979,5.531 3.99,6.448 3.01,0.917 10 false Rear Door Courtesy Light Switch Assembly RH 0.948,5.333 1.26,5.531 0.313,0.198 10 false Q24 0.219,6.469 3.281,6.823 3.063,0.354 10 false *2: w/ Curtain Shield Airbag 0.219,6.198 3.281,6.552 3.063,0.354 10 false *1: w/o Curtain Shield Airbag

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy Switch Status Front door courtesy light switch assembly RH signal Close or Open Close: Front door RH closed
Open: Front door RH open
-
FL Door Courtesy Switch Status Front door courtesy light switch assembly LH signal Close or Open Close: Front door LH closed
Open: Front door LH open
-
RR Door Courtesy Switch Status Rear door courtesy light switch assembly RH signal Close or Open Close: Rear door LH closed
Open: Rear door LH open
-
RL Door Courtesy Switch Status Rear door courtesy light switch assembly LH signal Close or Open Close: Rear door RH closed
Open: Rear door RH open
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy Switch Status
FL Door Courtesy Switch Status
RR Door Courtesy Switch Status
RL Door Courtesy Switch Status
50003 449 30,31,32,33
OK:

Normal conditions listed above are displayed.



Result:
Result Proceed to
OK A
NG ("FR Door Courtesy Switch Status" is abnormal) B
NG ("FL Door Courtesy Switch Status" is abnormal) C
NG ("RR Door Courtesy Switch Status" is abnormal) D
NG ("RL Door Courtesy Switch Status" is abnormal) E



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - POWER DISTRIBUTION BOX ASSEMBLY)

D

6.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

E

9.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
2.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the Q23 front door courtesy light switch assembly RH connector.


b.

Disconnect the 5F power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q23)Location & Routing

Click Connector(Q23)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Front Door Courtesy Light Switch Assembly RH

Q23-1 - 5F-5 Always Below 1 Ω
Q23-1 or 5F-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.


E438203C37
1.448,0.198 1.99,0.406 0.542,0.208 4.969,0.417 5.51,0.625 0.542,0.208 4.385,0.885 4.542,1.208 4.542,1.208 4.698,1.208 true 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 1.635,0.219 1.979,0.448 0.344,0.229 10 false 5F 5.125,0.438 5.469,0.667 0.344,0.229 10 false MB 4.76,1.115 5.156,1.344 0.396,0.229 10 false FRCY
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5F-5 - MB-4 (FRCY) Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

D

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - POWER DISTRIBUTION BOX ASSEMBLY)

*1: w/o Curtain shield airbag

*2: w/ Curtain shield airbag


a.

Disconnect the S14*1, S15*2 front door courtesy light switch assembly RH connector.


b.

Disconnect the 5F power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Curtain Shield Airbag
Tester Connection Condition Specified Condition

Click Location & Routing(S14)Location & Routing

Click Connector(S14)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Front Door Courtesy Light Switch Assembly LH

S14-1 - 5F-3 Always Below 1 Ω
S14-1 or 5F-3 - Body ground Always 10 kΩ or higher

w/ Curtain Shield Airbag
Tester Connection Condition Specified Condition

Click Location & Routing(S15)Location & Routing

Click Connector(S15)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Front Door Courtesy Light Switch Assembly LH

S15-1 - 5F-3 Always Below 1 Ω
S15-1 or 5F-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.


E438203C38
1.448,0.198 1.99,0.406 0.542,0.208 4.969,0.417 5.51,0.625 0.542,0.208 4.188,0.885 4.344,1.208 4.344,1.208 4.5,1.208 true 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 1.635,0.219 1.979,0.448 0.344,0.229 10 false 5F 5.135,0.438 5.479,0.667 0.344,0.229 10 false MB 4.573,1.146 4.969,1.375 0.396,0.229 10 false FLCY
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5F-3 - MB-2 (FLCY) Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

D

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

6.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

OK

7.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

7.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the Q24 rear door courtesy light switch assembly RH connector.


b.

Disconnect the 5F power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q24)Location & Routing

Click Connector(Q24)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Rear Door Courtesy Light Switch Assembly RH

Q24-1 - 5F-1 Always Below 1 Ω
Q24-1 or 5F-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.


E438203C33
1.458,0.219 1.979,0.427 0.521,0.208 5.01,0.354 5.531,0.563 0.521,0.208 4.604,1.26 4.406,1.26 4.406,1.26 4.073,0.885 true 0.229,0.115 0.542,0.271 0.313,0.156 10 false *a 5.167,0.375 5.896,0.99 0.729,0.615 10 false MB 1.646,0.26 1.917,0.448 0.271,0.188 10 false 5F 4.656,1.198 5.198,1.479 0.542,0.281 10 false RCTY
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5F-1 - MB-1 (RCTY) Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

D

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

9.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

OK

10.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - POWER DISTRIBUTION BOX ASSEMBLY)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

10.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the S16 rear door courtesy light switch assembly LH connector.


b.

Disconnect the 5F power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(S16)Location & Routing

Click Connector(S16)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Rear Door Courtesy Light Switch Assembly LH

S16-1 - 5F-26 Always Below 1 Ω
S16-1 or 5F-26 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.


E438203C34
1.448,0.198 1.99,0.406 0.542,0.208 4.969,0.417 5.51,0.625 0.542,0.208 4.604,0.896 4.76,1.219 4.76,1.219 4.917,1.219 true 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 1.635,0.219 1.979,0.448 0.344,0.229 10 false 5F 5.146,0.448 5.49,0.677 0.344,0.229 10 false MB 4.969,1.156 5.365,1.385 0.396,0.229 10 false LCTY
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5F-26 - MB-6 (LCTY) Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

D

REPLACE POWER DISTRIBUTION BOX ASSEMBLY