The main body ECU (multiplex network body ECU) detects the condition of the back door lock with courtesy light switch assembly (back door courtesy light switch).
w/ Power Back Door System:
w/o Power Back Door System:
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Courtesy Switch Status | Back door courtesy light switch signal | Close or Open | Close: Back door closed Open: Back door open |
- |
| Tester Display |
|---|
| Back Door Courtesy Switch Status |
Normal conditions listed above are displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/ Power Back Door System) | A |
| OK (w/o Power Back Door System) | B |
| NG | C |
A
B
C
Disconnect the g6 back door lock with courtesy light switch assembly connector.
Disconnect the 5F power distribution box assembly connector.
Disconnect the T3 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(g6)Location & Routingewd_type=routing;type=c;code=g6 Click Connector(g6)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assemblyewd_type=component;type=c;code=g6;pinno=4,1 |
||
| g6-4 (CTY) - 5F-2 | Always | Below 1 Ω |
| g6-4 (CTY) or 5F-2 - Body ground | Always | 10 kΩ or higher |
| g6-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power distribution box assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected (Power Distribution Box Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5F-2 - MB-19 (BCTY) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Disconnect the g4 back door lock with courtesy light switch assembly connector.
Disconnect the 5F power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(g4)Location & Routingewd_type=routing;type=c;code=g4 Click Connector(g4)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assemblyewd_type=component;type=c;code=g4;pinno=3,2 |
||
| g4-3 (+) - 5F-2 | Always | Below 1 Ω |
| g4-3 (+) or 5F-2 - Body ground | Always | 10 kΩ or higher |
| g4-2 (ACT-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power distribution box assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected (Power Distribution Box Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5F-2 - MB-19 (BCTY) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D