Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2021.04–2022.11
RM38G0E _58 Vehicle Interior _100749 LIGHTING (INT) _0468730 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Inside Handle Illumination Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

·

Front Door Inside Handle Illumination Light Assembly LH

·

Front Door Inside Handle Illumination Light Assembly RH

·

Rear Door Inside Handle Illumination Light Assembly LH

·

Rear Door Inside Handle Illumination Light Assembly RH


WIRING DIAGRAM

E463672E02
1.365,0.333 2.281,0.531 0.917,0.198 10 false DOME*1 2.635,0.167 5.083,0.365 2.448,0.198 10 false from DOME CUT Relay*1 2.615,0.708 5.063,0.906 2.448,0.198 10 false from Engine Stop and Start ECU*2 5.771,1.615 6.083,1.813 0.313,0.198 10 false 14 6.115,1.75 6.729,1.948 0.615,0.198 10 false LED2 5.5,4.885 7.135,5.24 1.635,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 5.51,4.729 5.969,4.927 0.458,0.198 10 false I2 2.313,1.854 2.469,2.052 0.156,0.198 10 false + 2.333,3.5 2.49,3.698 0.156,0.198 10 false + 2.344,5.188 2.5,5.385 0.156,0.198 10 false + 2.344,6.865 2.5,7.063 0.156,0.198 10 false + 3.365,3.51 3.521,3.708 0.156,0.198 10 false - 3.365,1.854 3.521,2.052 0.156,0.198 10 false - 3.354,5.198 3.51,5.396 0.156,0.198 10 false - 3.354,6.875 3.51,7.073 0.156,0.198 10 false - 3.615,1.583 3.771,1.781 0.156,0.198 10 false 2 2.094,3.281 2.25,3.479 0.156,0.198 10 false 1 2.115,4.948 2.271,5.146 0.156,0.198 10 false 1 2.115,6.656 2.271,6.854 0.156,0.198 10 false 1 2.063,1.563 2.219,1.76 0.156,0.198 10 false 1 3.604,3.292 3.76,3.49 0.156,0.198 10 false 2 3.625,4.979 3.781,5.177 0.156,0.198 10 false 2 3.646,6.646 3.802,6.844 0.156,0.198 10 false 2 1.792,2.219 4.063,2.646 2.271,0.427 10 false Front Door Inside Handle Illumination Light Assembly LH 1.792,2.063 2.25,2.26 0.458,0.198 10 false N8 1.74,3.781 2.198,3.979 0.458,0.198 10 false M10 1.729,3.927 3.979,4.333 2.25,0.406 10 false Front Door Inside Handle Illumination Light Assembly RH 1.823,5.427 2.281,5.625 0.458,0.198 10 false P5 1.813,5.604 4.094,5.969 2.281,0.365 10 false Rear Door Inside Handle Illumination Light Assembly LH 1.833,7.094 2.292,7.292 0.458,0.198 10 false O5 1.823,7.25 4.094,7.615 2.271,0.365 10 false Rear Door Inside Handle Illumination Light Assembly RH 0.146,8.438 2.885,8.813 2.74,0.375 10 false *2: w/ Stop and Start System 0.135,8.135 2.875,8.51 2.74,0.375 10 false *1: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

w/o Stop and Start System:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



HINT:

The DOME CUT relay supplies power to the interior lights. If all the lights that use power from the DOME CUT relay do not turn on, check the interior light auto cut circuit first.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>Interior Light Auto Cut Circuit


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Extended Illumination 2 Operation of the following lights:
·

Front door inside handle illumination light assembly RH

·

Front door inside handle illumination light assembly LH

·

Rear door inside handle illumination light assembly RH

·

Rear door inside handle illumination light assembly LH


OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Extended Illumination 2
50004 449 24
OK:

Door inside handle illumination light assembly turns on or off.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
2.CHECK HARNESS AND CONNECTOR (DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the N8 front door inside handle illumination light assembly LH connector.


b.

Disconnect the M10 front door inside handle illumination light assembly RH connector.


c.

Disconnect the P5 rear door inside handle illumination light assembly LH connector.


d.

Disconnect the O5 rear door inside handle illumination light assembly RH connector.


e.

Disconnect the I2 main body ECU (multiplex network body ECU) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N8,I2)Location & Routing

Click Connector(N8)Body>Front Door Wire LH>Front Door Inside Handle Illumination Light Assembly LH

Click Connector(I2)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

N8-2 (-) - I2-14 (LED2) Always Below 1 Ω
N8-2 (-) or I2-14 (LED2) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR