The automatic light control sensor detects ambient light. The sensor creates an electrical signal based on the amount of light detected, and sends the signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B124400 | Light Sensor Circuit Malfunction |
Detection condition:
The ignition switch is ON.
Malfunction status:
Either of the following conditions is met:
-
Malfunction in automatic light control sensor
-
Open or short in automatic light control sensor circuit
Malfunction duration:
5 seconds or more |
·
Automatic light control sensor
·
Harness or connector
·
Main body ECU (multiplex network body ECU) |
Main Body | A |
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Wait 10 seconds or more.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B124400 is not output | A |
| B124400 is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Cover the automatic light control sensor with an opaque object.
Procedure1
According to the display on the GTS, read the Data List and check that the value of Light Sensor Illuminance changes while performing the following:
Slowly move the opaque object to uncover and then cover the automatic light control sensor.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Light Sensor Illuminance | Automatic light control sensor illuminance | 0 to 8191 lx or SensorFail | Value is output according to ambient light level | The displayed value is "0" when no light is detected. |
| Tester Display |
|---|
| Light Sensor Illuminance |
The value changes according to the amount the automatic light control sensor is covered.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Pre-procedure1
Disconnect the K4 automatic light control sensor connector.
Disconnect the I3 main body ECU (multiplex network body ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(K4,I3)Location & Routingewd_type=routing;type=c,c;code=K4,I3 Click Connector(K4)Instrument Panel>No. 3 Instrument Panel Wire>Automatic Light Control Sensorewd_type=component;type=c;code=K4;pinno=1,4,2 |
||
| K4-1 (CLTB) - I3-8 (CLTB) | Always | Below 1 Ω |
| K4-4 (CLTS) - I3-20 (CLTS) | Always | Below 1 Ω |
| K4-2 (CLTE) - I3-21 (CLTE) | Always | Below 1 Ω |
| K4-1 (CLTB) or I3-8 (CLTB) - Body ground | Always | 10 kΩ or higher |
| K4-4 (CLTS) or I3-20 (CLTS) - Body ground | Always | 10 kΩ or higher |
| K4-2 (CLTE) or I3-21 (CLTE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Connect the I3 main body ECU (multiplex network body ECU) connector.
Procedure1
| *a | Component with harness connected (Main Body ECU (Multiplex Network Body ECU)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I3)Location & Routingewd_type=routing;type=c;code=I3 |
||
| I3-8 (CLTB) - I3-21 (CLTE) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC LIGHT CONTROL SENSOR>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG