Home › Audio / Visual / Telematics › AUDIO / VIDEO › ACTIVE NOISE CONTROL SYSTEM (for Type A)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467499 ACTIVE NOISE CONTROL SYSTEM(for Type A) C

AUDIO / VIDEO  ACTIVE NOISE CONTROL SYSTEM(for Type A)  B1AAA96  Rear Center Microphone Circuit Component Internal Failure  B1AAB1C  Rear Center Microphone Circuit Circuit Voltage Out of Range  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the No. 4 active noise control microphone system.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1AAA96 Rear Center Microphone Circuit Component Internal Failure Engine running, engine speed is 1200 rpm or higher 3 seconds after the ignition switch is turned to ACC, the stereo component equalizer assembly detects a malfunction in the No. 4 active noise control microphone for 4 seconds or more continuously*
·

Harness or connector

·

No. 4 active noise control microphone

·

Stereo component equalizer assembly


Active Noise Control A
B1AAB1C Rear Center Microphone Circuit Circuit Voltage Out of Range When the stereo component equalizer assembly detects a No. 4 active noise control microphone connection malfunction for 4 seconds or more continuously 3 seconds after the ignition switch is turned to ACC*
·

Harness or connector

·

No. 4 active noise control microphone

·

Stereo component equalizer assembly


Active Noise Control A

HINT:

*: Malfunction monitoring is not performed during the following conditions to prevent erroneous detection.

·

The battery voltage is less than 9.5 V.

·

Before 3 seconds have elapsed after the battery voltage has returned to normal.



WIRING DIAGRAM

E360402E98
5.75,0.792 6.26,1.031 0.51,0.24 10 false MC4+ 5.76,1.188 6.24,1.385 0.479,0.198 10 false MC4- 5.573,0.688 5.802,0.885 0.229,0.198 10 false 4 5.49,1.094 5.667,1.25 0.177,0.156 10 false 18 1.729,0.677 1.875,0.844 0.146,0.167 10 false 1 1.719,1.104 1.896,1.26 0.177,0.156 10 false 2 0.479,1.625 0.813,1.792 0.333,0.167 10 false d27 0.479,1.781 1.698,2.177 1.219,0.396 10 false No. 4 Active Noise Control Microphone 5.677,1.865 6.115,2.063 0.438,0.198 10 false S20 5.667,2.01 6.927,2.385 1.26,0.375 10 false Stereo Component Equalizer Assembly 1.208,0.75 1.646,0.948 0.438,0.198 10 false MC4+ 1.229,1.177 1.667,1.396 0.438,0.219 10 false MC4-

PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Active Noise Control > Clear DTCs
50002 415
Result:
Proceed to
NEXT




NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Active Noise Control > Trouble Codes
50001 415
Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B




A

B

3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - NO. 4 ACTIVE NOISE CONTROL MICROPHONE)
3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - NO. 4 ACTIVE NOISE CONTROL MICROPHONE)

Pre-procedure1

a.

Disconnect the S20 stereo component equalizer assembly connector.


b.

Disconnect the d27 No. 4 active noise control microphone connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(S20,d27)Location & Routing

Click Connector(S20)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assembly

Click Connector(d27)Body>No. 1 Roof Wire>Active Noise Control Microphone (Rear2 Center)

S20-4 (MC4+) - d27-1 (MC4+) Always Below 1 Ω
S20-18 (MC4-) - d27-2 (MC4-) Always Below 1 Ω
S20-4 (MC4+) - Body ground Always 10 kΩ or higher
S20-18 (MC4-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.REPLACE NO. 4 ACTIVE NOISE CONTROL MICROPHONE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE NO. 4 ACTIVE NOISE CONTROL MICROPHONE
a.

Replace the No. 4 active noise control microphone with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ACTIVE NOISE CONTROL MICROPHONE>REMOVAL



Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Active Noise Control > Clear DTCs
50002 415
Result:
Proceed to
NEXT




NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Active Noise Control > Trouble Codes
50001 415
Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B




A

END (NO. 4 ACTIVE NOISE CONTROL MICROPHONE IS DEFECTIVE)

B

REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY