Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467497 AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type, except 12.3 Inch Display)  B1324  Lost Communication with Meter  B1325  Lost Communication with HUD  


DESCRIPTION

These DTCs are stored when communication between the radio and display receiver assembly and combination meter assembly or meter mirror sub-assembly* is not possible.

*: w/ Headup Display


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1324 Lost Communication with Meter CAN reception error
·

Local bus communication line

·

Combination meter assembly power source circuit

·

Combination meter assembly

·

Radio and display receiver assembly

·

Harness or connector

·

No. 5 junction connector


Navigation System A
B1325 Lost Communication with HUD CAN reception error
·

Local bus communication line

·

Meter mirror sub-assembly power source circuit

·

Meter mirror sub-assembly

·

Radio and display receiver assembly

·

Harness or connector

·

No. 5 junction connector


Navigation System A

HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E464170E01
2.917,1.823 4.104,2.292 1.188,0.469 10 false Combination Meter Assembly 2.917,1.646 3.365,1.938 0.448,0.292 10 false I5 3.688,0.948 4.135,1.24 0.448,0.292 10 false ET 3.073,0.365 3.521,0.656 0.448,0.292 10 false B 3.083,1.302 3.531,1.594 0.448,0.292 10 false IG+ 2.885,0.302 3.333,0.594 0.448,0.292 10 false 5 2.885,1.208 3.333,1.5 0.448,0.292 10 false 6 3.99,0.25 4.438,0.542 0.448,0.292 10 false 14 3.99,0.552 4.438,0.844 0.448,0.292 10 false 30 4,0.854 4.448,1.146 0.448,0.292 10 false 2 4.365,0.26 4.813,0.552 0.448,0.292 10 false 2 4.302,0.552 4.75,0.844 0.448,0.292 10 false 13 5.552,0.26 6,0.552 0.448,0.292 10 false 3 5.521,0.552 5.969,0.844 0.448,0.292 10 false 14 5.917,0.26 6.365,0.552 0.448,0.292 10 false 5 5.854,1.156 7.052,1.615 1.198,0.458 10 false Radio and Display Receiver Assembly 5.927,0.552 6.375,0.844 0.448,0.292 10 false 6 5.844,0.979 6.792,1.542 0.948,0.563 10 false I13 6.083,0.396 7.031,0.958 0.948,0.563 10 false CNH1 6.083,0.698 7.031,1.26 0.948,0.563 10 false CNL1 2.083,0.521 3.229,0.854 1.146,0.333 10 false METER 1.958,1.438 2.813,1.781 0.854,0.344 10 false METER-IGR 3.031,4.396 4.125,4.823 1.094,0.427 10 false Meter Mirror Sub-assembly*1 3.021,4.219 3.635,4.365 0.615,0.146 10 false I17 1.792,3.354 2.875,3.625 1.083,0.271 10 false ECU-DCC NO.1 1.823,4.208 2.875,4.448 1.052,0.24 10 false ECU-IGR NO.2 4.313,4.781 6.656,5.063 2.344,0.281 10 false No. 5 CAN Junction Connector 4.323,4.604 4.823,4.813 0.5,0.208 10 false I122 3.083,3.208 3.531,3.5 0.448,0.292 10 false B 3.052,4.01 3.5,4.302 0.448,0.292 10 false IG 3.719,3.719 4.167,4.01 0.448,0.292 10 false ES 3.635,3.188 4.083,3.479 0.448,0.292 10 false TX+ 3.677,3.479 4.135,3.885 0.458,0.406 10 false TX- 3.969,3.063 4.417,3.354 0.448,0.292 10 false 14 3.969,3.365 4.417,3.656 0.448,0.292 10 false 15 4.375,3.073 4.823,3.365 0.448,0.292 10 false 1 4.313,3.365 4.76,3.656 0.448,0.292 10 false 12 3.979,3.625 4.427,3.917 0.448,0.292 10 false 4 2.885,3.135 3.333,3.427 0.448,0.292 10 false 2 2.885,3.948 3.333,4.24 0.448,0.292 10 false 1 1.031,5.448 3.573,5.792 2.542,0.344 10 false : Local Bus Communication Line 3.49,0.396 3.938,0.688 0.448,0.292 10 false MSCH 3.5,0.677 3.948,0.969 0.448,0.292 10 false MSCL 0.188,4.677 2.208,4.969 2.021,0.292 10 false *1: w/ Headup Display 0.135,4.052 2.208,4.521 2.073,0.469 10 false from IGR-NO.2 Relay*2 0.146,1.302 2.219,1.771 2.073,0.469 10 false from IGR-NO.1 Relay*2 0.792,0.365 1.708,0.833 0.917,0.469 10 false from Battery 0.698,3.219 1.719,3.406 1.021,0.188 10 false from Battery*2 0.25,0.792 1.594,1.281 1.344,0.49 10 false from Engine Stop and Start ECU*3 0.292,2.708 1.635,3.198 1.344,0.49 10 false from Engine Stop and Start ECU*3 0.26,3.563 1.604,4.052 1.344,0.49 10 false from Engine Stop and Start ECU*3 0.188,5.052 2.208,5.344 2.021,0.292 10 false *2: w/o Stop and Start System 2.25,5.052 4.271,5.344 2.021,0.292 10 false *3: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>PRECAUTION


PROCEDURE

1.CHECK DTC
a.

Check for DTCs and check that no DTCs are output.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>DTC CHECK / CLEAR


Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
B1324 and B1325 are not output A
B1324 and B1325 are output B
Only B1324 is output C
Only B1325 is output D



A

B

2.CHECK LOCAL BUS

C

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)

D

15.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY POWER SOURCE)
2.CHECK LOCAL BUS

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-3 - I122-14 Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Result:
Result Proceed to
I122-3 - I122-14 is less than or equal to 54 Ω A
I122-3 - I122-14 is more than or equal to 70 Ω B
None of the above conditions are met C



Post-procedure1

c.

None



A

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

B

10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

C

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-3 - I122-14 Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

NG

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-2 - I122-13 Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.CHECK VEHICLE TYPE

NG

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)
5.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Headup Display A
w/o Headup Display B



A

6.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

B

REPLACE NO. 5 CAN JUNCTION CONNECTOR

6.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-1 - I122-12 Cable disconnected from negative (-) battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE NO. 5 CAN JUNCTION CONNECTOR

NG

7.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)
7.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I17 meter mirror sub-assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I17)Location & Routing

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

I17-14 (TX+) - I17-15 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I5 combination meter assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I5)Location & Routing

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I5-14 (MSCH) - I5-30 (MSCL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I13 radio and display receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-5 (CNH1) - I13-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I13 radio and display receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-5 (CNH1) - I13-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)
11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 CAN junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-3 - I122-14 Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE NO. 5 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)

Pre-procedure1

a.

Disconnect the I5 combination meter assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I5)Location & Routing

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I5-2 (ET) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I5)Location & Routing

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I5-5 (B) - Body ground Always 11 to 14 V
I5-6 (IG+) - Body ground Ignition switch ON 10.5 to 16 V*1
11 to 14 V*2


*1: w/ Stop and Start System

*2: w/o Stop and Start System


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 CAN junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-2 - I122-13 Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

17.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

NG

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)
14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I5 combination meter assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I5)Location & Routing

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I5-14 (MSCH) - I5-30 (MSCL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY POWER SOURCE)

Pre-procedure1

a.

Disconnect the I17 meter mirror sub-assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I17)Location & Routing

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

I17-4 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I17)Location & Routing

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

I17-2 (B) - Body ground Always 10.5 to 16 V*1
11 to 14 V*2
I17-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V*1
11 to 14 V*2


*1: w/ Stop and Start System

*2: w/o Stop and Start System


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

16.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 CAN junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-1 - I122-12 Cable disconnected from negative (-) battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

17.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

NG

19.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)
17.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 CAN junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-3 - I122-14 Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE NO. 5 CAN JUNCTION CONNECTOR

NG

18.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)
18.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I13 radio and display receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-5 (CNH1) - I13-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I17 headup display (meter mirror sub-assembly) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I17)Location & Routing

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

I17-14 (TX+) - I17-15 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR