Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467495 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

The radio receiver assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E465235E02
1.031,2.281 2.99,2.531 1.958,0.25 10 false Combination Meter Assembly 1.052,2.135 1.51,2.333 0.458,0.198 10 false I6 4.823,1.49 5.24,1.75 0.417,0.26 10 false SPD 4.427,2.302 6.813,2.625 2.385,0.323 10 false Radio Receiver Assembly 4.438,2.146 4.896,2.344 0.458,0.198 10 false I9 2.125,1.49 2.542,1.75 0.417,0.26 10 false +S 2.458,1.375 2.875,1.635 0.417,0.26 10 false 35 4.542,1.375 4.958,1.635 0.417,0.26 10 false 17 1.604,0.344 4.052,0.542 2.448,0.198 10 false to Other Systems

CAUTION / NOTICE / HINT

NOTICE:

The audio and visual system troubleshooting procedure is based on the premise that the meter/gauge system is operating normally. Check the meter/gauge system first before troubleshooting the audio and visual system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
B611998C01
1.479,0.146 1.896,0.365 0.417,0.219 0.656,1.802 1.01,1.385 true 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.594,0.167 1.906,0.365 0.313,0.198 10 false I6 0.469,1.833 0.781,2.031 0.313,0.198 10 false +S 2.792,3.583 3.188,3.854 0.396,0.271 10 false GND 1.083,3.896 1.479,4.167 0.396,0.271 10 false (A)
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


ii.

Connect an oscilloscope to terminal I6-35 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I6-35 (+S) - Body ground
Tool setting 5 V/DIV, 20 ms./DIV
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I9 radio receiver assembly connector.


b.

Disconnect the I6 combination meter assembly connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR