Home › General › MAINTENANCE › FRONT BRAKE FLEXIBLE HOSE
RM38G0E _V1 General _100461 MAINTENANCE _0468808 FRONT BRAKE FLEXIBLE HOSE A

MAINTENANCE  FRONT BRAKE FLEXIBLE HOSE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C455968N01
4.167,4.167 7.083,5.667 2.917,1.5 0.083,0.25 3,1.75 2.917,1.5 6.5,0.146 6.917,0.146 false 6.5,0.604 6.833,0.604 false 6.531,1.021 6.865,1.021 false 5.583,4.917 5.75,4.917 false 1.458,0.583 1.708,0.583 false 4.833,4.813 4.833,4.479 4.833,4.479 5,4.479 false 0.833,1.219 0.833,0.885 0.833,0.885 1,0.885 false 4.25,4.25 4.583,4.5 0.333,0.25 10 false *A 0.167,0.333 0.5,0.583 0.333,0.25 10 false *B 0.417,1.104 0.75,1.354 0.333,0.25 10 false x 3 5.563,5.427 5.896,5.677 0.333,0.25 10 false x 3 6.344,0.031 6.677,0.365 0.333,0.333 18 false 1 6.323,0.469 6.656,0.802 0.333,0.333 18 false 2 6.344,0.896 6.677,1.229 0.333,0.333 18 false 4 5.417,4.802 5.75,5.135 0.333,0.333 18 false 3 1.292,0.458 1.625,0.792 0.333,0.333 18 false 3 5.063,4.354 5.396,4.688 0.333,0.333 18 false 5 1.063,0.771 1.396,1.104 0.333,0.333 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - - - (Click here)
3 REMOVE FRONT WHEEL - - - -
4 DRAIN BRAKE FLUID - - (Click here) -
5 FRONT FENDER APRON TRIM PACKING D 53785B - - -
6 FRONT FENDER APRON TRIM PACKING C 53784 - - -

*A for LH Side *B for RH Side

C455969N01
2.417,0.917 2.667,0.917 2.667,0.917 3.344,2.333 true 3.792,0.521 4.208,0.521 false 4.552,0.854 4.969,0.854 false 6.625,2.167 6.792,2.167 false 6,1.833 6,1.583 6,1.583 6.25,1.583 false 0.25,0.25 0.667,0.583 0.417,0.333 10 false *A 2.24,0.802 2.49,1.219 0.25,0.417 18 false 7 4.25,0.458 4.667,0.792 0.417,0.333 10 false *1 5.021,0.76 5.271,1.01 0.25,0.25 10 false ● 6.844,2.073 7.094,2.323 0.25,0.25 10 false ● 6.313,1.49 6.563,1.74 0.25,0.25 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

7 FRONT FLEXIBLE HOSE 47313J (Click here) - -

*A for LH Side - -
*1 BRAKE TUBE - -
● Non-reusable part - -

C455970N01
4.448,3.604 5.031,2.854 5.031,2.854 5.448,2.854 true 0.896,0.417 1.229,0.417 false 2.75,2.844 2.75,3.01 2.75,3.01 1.333,3.01 true 4.583,0.833 4.75,0.833 4.75,0.833 4.75,1 false 4.333,1 5.083,1 false 4.458,0.917 4.75,0.917 false 1.75,1.083 1.75,0.667 1.75,0.667 2.083,0.667 false 1.833,0.917 1.833,0.667 false 2.667,5.5 3,5.5 false 3.531,5.563 3.531,5.396 3.531,5.396 3.698,5.396 false 2.969,0.667 3.385,0.667 false 2.823,2.719 2.823,1.302 2.823,1.302 2.688,1.302 true 0.573,2.094 1.156,2.094 1.156,2.094 1.156,2.26 false 0.844,2.094 0.844,2.427 false 6.083,0.5 6.333,0.5 false 1.75,3.083 3.083,3.083 true 1.75,3.083 1.75,5.417 true 1.75,5.417 3.083,5.417 true 3.083,3.083 3.083,5.417 true 2.438,3.458 2.438,4.875 2.438,4.875 2.188,4.875 true 5.781,2.729 6.115,3.063 0.333,0.333 18 false 8 0.708,0.292 1.042,0.625 0.333,0.333 18 false 9 1.01,2.875 1.427,3.208 0.417,0.333 18 false 13 5.135,0.896 5.385,1.146 0.25,0.25 10 false ● 2.146,0.594 2.396,0.844 0.25,0.25 10 false ● 2.531,5.406 2.781,5.656 0.25,0.25 10 false ● 3.75,5.302 4,5.552 0.25,0.25 10 false ● 3.438,0.604 3.771,0.854 0.333,0.25 10 false *1 0.25,0.25 0.583,0.5 0.333,0.25 10 false *A 2.385,1.146 2.802,1.479 0.417,0.333 18 false 12 0.406,2.031 0.74,2.281 0.333,0.25 10 false *1 6.385,0.375 6.802,0.792 0.417,0.417 18 false 10 1.854,4.75 2.271,5.083 0.417,0.333 18 false 11 1.833,3.167 2.083,3.417 0.25,0.25 10 true *B

Procedure Part Name Code
Z101186

Z101188

Z101187

8 FRONT FLEXIBLE HOSE 47313A (Click here) - -
9 NO. 2 BRAKE TUBE HEAT INSULATOR 47394 - - -
10 BRAKE TUBE HEAT INSULATOR 47393 - - -
11 FRONT STABILIZER CONTROL TUBE ASSEMBLY - - - -
12 FRONT BRAKE TUBE FLEXIBLE HOSE 47311G (Click here) - -
13 FRONT BRAKE TUBE FLEXIBLE HOSE 47315B (Click here) - -

*A for RH Side *B w/ Electronic-Kinetic Dynamic Suspension System
*1 BRAKE TUBE - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front brake flexible hose removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

NOTICE:
·

While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.

·

If both left and right front flexible hoses are disconnected at the same time, be sure to place an identification mark on each hose to indicate its installation position.



HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISABLE BRAKE CONTROL

Z101186

Click here(Click here)

Hide 3.REMOVE FRONT WHEEL

Hide 4.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 53785B 5.REMOVE FRONT FENDER APRON TRIM PACKING D (for LH Side)

a.
C455971


Hide 53784 6.REMOVE FRONT FENDER APRON TRIM PACKING C (for RH Side)

a.

Use the same procedure as for the front fender apron trim packing D.


Hide 47313J 7.REMOVE FRONT FLEXIBLE HOSE (for LH Side)

a.
C455972N01
0.417,0.25 0.75,0.5 0.333,0.25 18 false i 3.833,0.25 4.167,0.5 0.333,0.25 18 false ii 1.74,2.76 2.49,3.177 0.75,0.417 18 false iii, iv

i.

Remove the union bolt and gasket, and disconnect the front flexible hose from the disc brake cylinder assembly.


ii.

Remove the 2 bolts and separate the front flexible hose from the steering knuckle and vehicle body.


iii.

Using a union nut wrench, disconnect the brake tube while holding the front flexible hose with a wrench.

NOTICE:
·

Do not kink or damage the brake tube.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.




iv.

Remove the clip and front flexible hose from the vehicle body.



Hide 47313A 8.REMOVE FRONT FLEXIBLE HOSE (for RH Side)

a.

Use the same procedure as for the LH side.


Hide 47394 9.REMOVE NO. 2 BRAKE TUBE HEAT INSULATOR (for RH Side)

a.
C455974


Hide 47393 10.REMOVE BRAKE TUBE HEAT INSULATOR (for RH Side)

a.
C459900


Hide 11.DISCONNECT FRONT STABILIZER CONTROL TUBE ASSEMBLY (for RH Side, w/ Electronic-Kinetic Dynamic Suspension System)

a.
C459901


Hide 47311G 12.REMOVE BRAKE TUBE FLEXIBLE HOSE (for RH Side)

a.
C455975N01
0.385,0.042 0.99,0.417 0.604,0.375 18 false i, ii

i.

Using a union nut wrench, disconnect the brake tube while holding the front brake tube flexible hose with a wrench.

NOTICE:
·

Do not kink or damage the brake tube.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.




ii.

Remove the 2 clips and front brake tube flexible hose from the vehicle body.



Hide 47315B 13.REMOVE BRAKE TUBE FLEXIBLE HOSE (for RH Side)

a.
C455976N01
0.385,0.052 1.052,0.635 0.667,0.583 18 false i, ii

i.

Using a union nut wrench, disconnect the brake tube while holding the front brake tube flexible hose with a wrench.

NOTICE:
·

Do not kink or damage the brake tube.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.




ii.

Remove the 2 clips and front brake tube flexible hose from the vehicle body.