Home › Brake › BRAKE (REAR) › REAR BRAKE › 2021.04–2021.07
RM38G0E _54 Brake _100996 BRAKE (REAR) _0468750 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C457776N02
6.427,1.063 6.844,1.063 false 5.75,2.5 6.167,2.5 false 6.427,0.198 6.875,0.198 false 6.417,0.646 6.792,0.646 false 6.229,2.365 6.479,2.698 0.25,0.333 18 false 2 6.24,0.052 6.51,0.438 0.271,0.385 18 false 1 6.25,0.927 6.667,1.26 0.417,0.333 18 false 4 6.24,0.5 6.49,0.833 0.25,0.333 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 REAR WHEEL - - - -
3 DISABLE BRAKE CONTROL - - - (Click here)
4 DRAIN BRAKE FLUID - - - -

C455988N01
0.083,2.198 1.5,3.615 1.417,1.417 1.667,4.75 2.75,5.5 1.083,0.75 1.75,3.167 3.25,4.667 1.5,1.5 1.417,0.25 3.083,2.083 1.667,1.833 3.792,4.333 5.208,5.75 1.417,1.417 2.167,0.667 2.167,0.417 2.167,0.417 2.417,0.417 false 5.844,0.719 6.177,0.719 false 4.333,3.167 4.583,3.167 4.583,3.167 4.583,2.917 false 3.417,1.854 3.417,1.438 3.417,1.438 3.573,1.438 false 6,2.083 6,1.75 6,1.75 5.583,1.75 false 4,0.667 4.333,0.667 false 5.75,3.75 5.75,4 5.75,4 5.917,4 false 2.167,3.167 2.167,2.833 2.167,2.833 2.417,2.833 false 5.208,5.25 5.375,5.25 false 3.5,1.25 3.75,1.25 3.75,1.25 3.75,1.083 false 3.604,1.25 3.604,0.958 false 4.417,2.167 4.417,1.917 4.417,1.917 4.583,1.917 false 0.583,3.948 0.417,3.948 0.417,3.948 0.417,3.615 false 2,5.25 2.5,5.25 false 2,4.917 2.167,4.917 2.167,4.917 2.167,5.25 false 4.188,4.583 4.521,4.583 false 4.5,5.5 4.833,5.5 false 0.615,3.333 0.948,3.333 false 0.396,2.417 0.729,2.417 false 1.5,4.917 1.667,4.917 false 2.25,3.417 2.917,3.417 false 2.75,3.417 2.75,3.667 false 2.479,0.302 2.896,0.719 0.417,0.417 18 false 5 6.542,0.594 6.958,1.01 0.417,0.417 18 false 6 3.875,1.302 4.292,1.719 0.417,0.417 18 false 7 4.146,3.052 4.563,3.469 0.417,0.417 18 false 8 3.99,3.073 4.24,3.406 0.25,0.333 10 false ● 5.417,1.583 5.917,1.917 0.5,0.333 18 false 9 1.781,1.333 2.115,1.583 0.333,0.25 10 false x 2 6.667,2.188 7,2.438 0.333,0.25 10 false x 2 3.229,2.427 3.563,2.677 0.333,0.25 10 false x 2 4.583,2.042 4.917,2.292 0.333,0.25 10 false x 2 4.385,0.531 4.885,0.865 0.5,0.333 18 false 10 5.969,3.875 6.469,4.208 0.5,0.333 18 false 11 2.469,2.708 2.969,3.042 0.5,0.333 18 false 12 3.365,1.156 3.615,1.49 0.25,0.333 10 false ● 4.635,1.823 4.885,2.156 0.25,0.333 10 false ● 5.688,5.125 6.188,5.458 0.5,0.333 18 false 13 1.167,4.802 1.667,5.135 0.5,0.333 18 false 13 0.875,3.844 1.375,4.177 0.5,0.333 18 false 13 1.5,0.333 1.833,0.583 0.333,0.25 10 false *A 4.573,4.521 4.823,4.771 0.25,0.25 10 false *1 4.323,5.427 4.573,5.677 0.25,0.25 10 false *2 0.448,3.26 0.698,3.51 0.25,0.25 10 false *1 0.781,2.354 1.031,2.604 0.25,0.25 10 false *2 1.708,5.188 2.125,5.438 0.417,0.25 10 false ● *3 2.969,3.354 3.219,3.604 0.25,0.25 10 false *4

Procedure Part Name Code
Z101186

Z101188

Z101187

5 PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY 46170 - - -
6 NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A (Click here) - -
7 PARKING BRAKE ACTUATOR ASSEMBLY 46310B (Click here) - -
8 PARKING BRAKE ACTUATOR SEAL 46310C - - -
9 REAR DISC BRAKE DUST BOOT PROTECTOR 47877 (Click here) - -
10 REAR FLEXIBLE HOSE 47319F - - -
11 REAR DISC BRAKE CYLINDER ASSEMBLY 47850 - - -
12 REAR DISC BRAKE PAD KIT 04466 - - -
13 REAR DISC BRAKE ANTI-SQUEAL SHIM KIT 04946 (Click here) - -

*A w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY - -
*1 REAR NO. 1 DISC BRAKE ANTI-SQUEAL SHIM *2 REAR NO. 2 DISC BRAKE ANTI-SQUEAL SHIM
*3 REAR DISC BRAKE PAD WEAR INDICATOR PLATE *4 REAR DISC BRAKE PAD
● Non-reusable part - -

C455989N01
4.083,0.25 5.583,1.833 1.5,1.583 3.667,2.667 4.333,4.083 0.667,1.417 5.583,1 6,1 false 2.365,1.51 2.698,1.51 false 3.417,3.417 3.667,3.417 false 4.5,3.208 4.5,2.708 4.5,2.708 4.833,2.708 false 4.167,4.417 4.5,4.417 4.5,4.417 4.5,4.167 false 4.833,3.354 4.833,3.104 4.833,3.104 5.083,3.104 false 6,4.083 6.333,4.083 false 3.917,3 3.917,3.25 3.917,3.25 4.083,3.25 false 3.917,3.667 3.917,3.5 3.917,3.5 4.083,3.5 false 6.333,0.906 6.917,1.24 0.583,0.333 18 false 14 3.094,3.292 3.677,3.625 0.583,0.333 18 false 15 3.042,1.385 3.625,1.719 0.583,0.333 18 false 19 5.344,2.583 5.927,2.917 0.583,0.333 18 false 16 5.198,2.646 5.531,2.979 0.333,0.333 10 false ● 3.854,4.302 4.438,4.635 0.583,0.333 18 false 17 3.698,4.354 4.031,4.688 0.333,0.333 10 false ● 5.146,3.052 5.479,3.385 0.333,0.333 10 false ● 5.292,2.99 5.875,3.323 0.583,0.333 18 false 17 6.396,3.958 6.979,4.292 0.583,0.333 18 false 18 4.917,4.552 5.333,4.802 0.417,0.25 10 false x 2 4.135,3.188 4.385,3.438 0.25,0.25 10 false *2 4.135,3.438 4.385,3.688 0.25,0.25 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

14 REAR DISC BRAKE PAD SUPPORT PLATE - (Click here) - -
15 REAR DISC BRAKE CYLINDER SLIDE PIN - - - -
16 REAR DISC BRAKE CYLINDER SLIDE BUSHING - (Click here) - -
17 REAR DISC BRAKE BUSHING DUST BOOT - - - -
18 REAR DISC BRAKE CYLINDER MOUNTING 47822 - - -
19 REAR DISC 42321 (Click here) - -

*1 REAR NO. 1 DISC BRAKE CYLINDER SLIDE PIN *2 REAR NO. 2 DISC BRAKE CYLINDER SLIDE PIN
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear brake removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.



HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)

·

Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.

Click here(Click here)




Hide 2.REMOVE REAR WHEEL

Hide 3.DISABLE BRAKE CONTROL

a.
C455990N01
0.417,0.063 1,0.479 0.583,0.417 18 false i

i.

Perform the following procedure:

1.

Wait 2 minutes after turning the ignition switch off to ensure that the skid control ECU is in sleep mode.

NOTICE:
·

When the brake pedal is depressed or the door courtesy switch is turned on even if the ignition switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.

·

Do not operate the electric parking brake switch assembly when the electric parking brake system is in rear brake pad replacement mode.



2.

except 1GR-FE:

for LHD:

Remove the engine side cover LH.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL

for RHD:

Remove the engine side cover RH.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL

3.

Disconnect the connector from the brake master cylinder reservoir assembly.

4.

Disconnect the cable from the negative (-) battery terminal.

for 1GR-FE:

Click hereGeneral>MAINTENANCE>1GR-FE BATTERY>REMOVAL

for V35A-FTS:

Click hereGeneral>MAINTENANCE>V35A-FTS BATTERY>REMOVAL

5.

In order to prevent pressurized brake fluid in the accumulator from being applied to the brake calipers, depress the brake pedal 40 times or more to return the pressurized brake fluid in the accumulator back to the brake master cylinder reservoir assembly.

6.

Check that the brake pedal cannot be further depressed.




Hide 4.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 46170 5.REMOVE PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY (w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY)

Hide 890C0A 6.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Z101186

Click here(Click here)

Hide 46310B 7.REMOVE PARKING BRAKE ACTUATOR ASSEMBLY

Z101186

Click here(Click here)

Hide 46310C 8.REMOVE PARKING BRAKE ACTUATOR SEAL

Hide 47877 9.REMOVE REAR DISC BRAKE DUST BOOT PROTECTOR

Z101186

Click here(Click here)

Hide 47319F 10.SEPARATE REAR FLEXIBLE HOSE

a.
C455992


Hide 47850 11.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C455993


Hide 04466 12.REMOVE REAR DISC BRAKE PAD KIT

a.
C455994


Hide 04946 13.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

Z101186

Click here(Click here)

Hide 14.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

Z101186

NOTICE:

Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.



a.
C455995


Hide 15.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C455996C01
4.771,0.417 5.104,0.417 true 4.635,1.417 5.052,1.417 true 5.104,1.354 5.354,1.604 0.25,0.25 10 false *1 5.156,0.354 5.49,0.604 0.333,0.25 10 false *2
*1 Rear No. 1 Disc Brake Cylinder Slide Pin *2 Rear No. 2 Disc Brake Cylinder Slide Pin



Hide 16.REMOVE REAR DISC BRAKE CYLINDER SLIDE BUSHING

a.
C455997N01
0.417,0.052 1.167,0.469 0.75,0.417 18 false i

i.

Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the rear No. 2 disc brake cylinder slide pin.

NOTICE:

Do not damage the rear No. 2 disc brake cylinder slide pin.




Hide 17.REMOVE REAR DISC BRAKE BUSHING DUST BOOT

a.
C456283


Hide 47822 18.REMOVE REAR DISC BRAKE CYLINDER MOUNTING

a.
C456284


Hide 42431 19.REMOVE REAR DISC

a.
C456285C01
3.427,1.219 4.583,1.333 4.583,1.333 3.448,1.156 true 4.635,1.271 4.969,1.521 0.333,0.25 10 false *a 0.417,0.063 1.083,0.479 0.667,0.417 18 false i, ii
*a Matchmark - -


i.

Put matchmarks on the rear disc and rear axle shaft.


ii.

Remove the rear disc.