Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100607 NAVIGATION / MULTI INFO DISPLAY _0467503 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Vehicle Speed Signal Circuit between Navigation ECU and Combination Meter  


DESCRIPTION

The navigation ECU assembly receives a vehicle speed signal from the combination meter assembly.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E466178E01
0.948,2.375 2.906,2.625 1.958,0.25 10 false Combination Meter Assembly 0.948,2.219 1.406,2.417 0.458,0.198 10 false I6 4.823,1.49 5.24,1.75 0.417,0.26 10 false SPD 4.615,2.354 6.573,2.604 1.958,0.25 10 false Navigation ECU Assembly 4.615,2.188 5.073,2.385 0.458,0.198 10 false I21 2.125,1.49 2.542,1.75 0.417,0.26 10 false +S 2.458,1.375 2.875,1.635 0.417,0.26 10 false 35 4.594,1.375 5.01,1.635 0.417,0.26 10 false 9 1.604,0.344 4.052,0.542 2.448,0.198 10 false to Other Systems

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E396774C48
1.448,0.188 1.948,0.5 0.5,0.313 0.844,2.052 1.229,1.521 true 0.635,2.063 0.948,2.26 0.313,0.198 10 false +S 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.635,0.24 1.948,0.438 0.313,0.198 10 false I6 2.802,3.604 3.26,3.802 0.458,0.198 10 false GND 1.125,3.875 1.344,4.094 0.219,0.219 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


ii.

Connect an oscilloscope to terminal I6-35 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I6-35 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.INSPECT NAVIGATION ECU ASSEMBLY (INPUT WAVEFORM)

NG

2.INSPECT NAVIGATION ECU ASSEMBLY (INPUT WAVEFORM)
a.
E401096C29
1.49,0.417 1.906,0.667 0.417,0.25 0.875,1.021 0.76,0.635 true 2.781,3.604 3.24,3.802 0.458,0.198 10 false GND 1.125,3.854 1.438,4.135 0.313,0.281 10 false A 0.625,0.448 0.979,0.729 0.354,0.281 10 false SPD 0.115,0.094 0.469,0.375 0.354,0.281 10 false *a 1.583,0.458 1.938,0.74 0.354,0.281 10 false I21
*a Component with harness connected
(Navigation ECU Assembly)


Check the input waveform.

i.

Remove the navigation ECU assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


ii.

Connect an oscilloscope to terminal I21-9 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I21-9 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR