Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100607 NAVIGATION / MULTI INFO DISPLAY _0467503 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E466179E04
4.167,2.49 6.615,2.76 2.448,0.271 10 false Stereo Component Amplifier Assembly 0.938,2.448 4.917,2.646 3.979,0.198 10 false Combination Meter Assembly 0.927,2.281 1.24,2.479 0.313,0.198 10 false I6 2.104,1.625 2.417,1.823 0.313,0.198 10 false +S 2.448,1.49 2.76,1.688 0.313,0.198 10 false 35 1.573,0.49 4.021,0.688 2.448,0.198 10 false to Other Systems 4.823,1.625 5.281,1.823 0.458,0.198 10 false SPD 4.042,1.51 5.573,1.708 1.531,0.198 10 false 16*1, 17*2 4.188,2.292 6.021,2.49 1.833,0.198 10 false S22 0.24,2.865 2.688,3.135 2.448,0.271 10 false *1: for 10 Speakers 0.24,3.188 2.688,3.458 2.448,0.271 10 false *2: for 14 Speakers

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E396774C45
1.448,0.188 1.948,0.5 0.5,0.313 0.698,2.052 1.083,1.521 true 0.573,2.063 0.885,2.26 0.313,0.198 10 false +S 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.646,0.271 1.958,0.469 0.313,0.198 10 false I6 2.802,3.604 3.26,3.802 0.458,0.198 10 false GND 1.125,3.875 1.344,4.094 0.219,0.219 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


ii.

Connect an oscilloscope to terminal I6-35 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I6-35 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)

NG

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)
a.
E276235C27
1.604,0.167 1.958,0.427 0.354,0.26 2.333,2.135 2.823,1.333 true 2.938,2.198 2.979,1.333 true 0.083,0.083 0.333,0.25 0.25,0.167 10 false *a 1.667,0.219 2,0.385 0.333,0.167 10 false S22 2.01,2.177 2.594,2.354 0.583,0.177 10 true SPD*A 2.802,3.583 3.135,3.75 0.333,0.167 10 false GND 1.146,3.833 1.396,4 0.25,0.167 10 false A 2.771,2.25 3.354,2.427 0.583,0.177 10 false SPD*B
*A for 14 Speakers
*B for 10 Speakers
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Check the input waveform.

*1: for 10 Speakers

*2: for 14 Speakers


i.

Remove the stereo component amplifier assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


ii.

Connect an oscilloscope to terminal S22-16 (SPD)*1 or S22-17 (SPD)*2 and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal
·

S22-16 (SPD) - Body ground*1

·

S22-17 (SPD) - Body ground*2


Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR