Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100607 NAVIGATION / MULTI INFO DISPLAY _0467503 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1324  Lost Communication with Meter  B1325  Lost Communication with HUD  


DESCRIPTION

These DTCs are stored when communication between the radio receiver assembly and combination meter assembly or headup display (meter mirror sub-assembly)* is not possible.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1324 Lost Communication with Meter CAN reception error
·

Local bus communication line

·

Combination meter power source circuit

·

Combination meter assembly

·

Radio receiver assembly

·

Harness or connector

·

No. 5 junction connector


Navigation System A
B1325 Lost Communication with HUD CAN reception error
·

Local bus communication line

·

Headup display (meter mirror sub-assembly) power source circuit

·

Headup display (meter mirror sub-assembly)

·

Radio receiver assembly

·

Harness or connector

·

No. 5 junction connector


Navigation System A

*: w/ Headup Display System


HINT:

The radio receiver assembly is the master unit.


WIRING DIAGRAM

E466167E02
3.74,1.646 4.198,1.844 0.458,0.198 10 false I13 3.729,1.813 4.677,2.167 0.948,0.354 10 false Radio Receiver Assembly 4.208,0.708 4.823,0.906 0.615,0.198 10 false CNH1 3.813,2.906 3.969,3.104 0.156,0.198 10 false B 4.208,1.271 4.823,1.469 0.615,0.198 10 false CNL1 3.813,3.479 4.271,3.677 0.458,0.198 10 false IG+ 5.313,7.333 5.927,7.531 0.615,0.198 10 false I122 3.823,7 4.135,7.198 0.313,0.198 10 false IG 5.313,7.521 7.156,7.771 1.844,0.25 10 false No. 5 Junction Connector 3.552,4.542 4.74,4.938 1.188,0.396 10 false Combination Meter Assembly 3.542,4.354 4,4.552 0.458,0.198 10 false I5 4.385,6.938 4.698,7.135 0.313,0.198 10 false ES 4.375,4 4.688,4.198 0.313,0.198 10 false ET 3.51,7.302 3.969,7.5 0.458,0.198 10 false I17 3.5,7.49 4.948,7.865 1.448,0.375 10 false Headup Display (Meter Mirror Sub-assembly)*1 4.333,5.74 4.792,5.938 0.458,0.198 10 false TX+ 4.167,2.938 4.625,3.135 0.458,0.198 10 false MSCH 4.188,3.49 4.646,3.688 0.458,0.198 10 false MSCL 4.365,6.313 4.823,6.51 0.458,0.198 10 false TX- 3.802,5.74 3.958,5.938 0.156,0.198 10 false B 0.396,3.979 1.74,4.333 1.344,0.354 10 false from Engine Stop and Start ECU*2 0.448,4.917 1.792,5.271 1.344,0.354 10 false from Engine Stop and Start ECU*2 0.417,6.188 1.76,6.542 1.344,0.354 10 false from Engine Stop and Start ECU*2 0.177,7.427 2.5,7.708 2.323,0.281 10 false *1: w/ Headup Display System 0.344,6.99 2.667,7.271 2.323,0.281 10 false from IGR-NO.2 Relay*3 1.052,8.385 3.375,8.667 2.323,0.281 10 false : Local Bus Communication Line 2.135,7.135 3.281,7.417 1.146,0.281 10 false ECU-IGR NO.2 2.198,5.896 3.344,6.177 1.146,0.281 10 false ECU-DCC NO.1 3.542,5.615 3.698,5.813 0.156,0.198 10 false 2 3.573,6.854 3.729,7.052 0.156,0.198 10 false 1 4.698,0.667 4.854,0.865 0.156,0.198 10 false 5 4.708,1.313 4.865,1.51 0.156,0.198 10 false 6 5.344,1.323 5.802,1.521 0.458,0.198 10 false 14 5.396,0.656 5.552,0.854 0.156,0.198 10 false 3 4.698,5.583 5.01,5.781 0.313,0.198 10 false 14 4.719,6.146 5.031,6.344 0.313,0.198 10 false 15 4.708,6.813 4.865,7.01 0.156,0.198 10 false 4 0.896,5.719 1.906,5.969 1.01,0.25 10 false from Battery*3 2.396,3.104 3.167,3.302 0.771,0.198 10 false METER 2.229,3.646 3.177,3.875 0.948,0.229 10 false METER-IGR 0.188,7.75 2.51,8.031 2.323,0.281 10 false *2: w/ Stop and Start System 0.188,8.063 2.51,8.344 2.323,0.281 10 false *3: w/o Stop and Start System 0.344,3.5 2.667,3.781 2.323,0.281 10 false from IGR-NO.1 Relay*3 1,2.896 3.323,3.177 2.323,0.281 10 false from Battery 3.552,2.802 3.708,3 0.156,0.198 10 false 5 3.563,3.344 3.719,3.542 0.156,0.198 10 false 6 4.698,2.76 5.01,2.958 0.313,0.198 10 false 14 4.698,3.333 5.01,3.531 0.313,0.198 10 false 30 4.708,3.885 4.865,4.083 0.156,0.198 10 false 2 5.344,6.146 5.656,6.344 0.313,0.198 10 false 12 5.385,5.583 5.542,5.781 0.156,0.198 10 false 1 5.385,2.771 5.542,2.969 0.156,0.198 10 false 2 5.333,3.323 5.646,3.521 0.313,0.198 10 false 13

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:

B1324 and B1325 will not continue to output when clear DTC is performed even if the malfunction continues.


PROCEDURE

1.CHECK DTC
a.

Check for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
B1324 and B1325 are not output A
B1324 and B1325 are output B
Only B1324 is output C
Only B1325 is output D



A

B

2.CHECK LOCAL BUS

C

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)

D

14.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE)
2.CHECK LOCAL BUS

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-3 - I122-14 Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Result:
Result Proceed to
I122-3 - I122-14 is less than or equal to 54 Ω A
I122-3 - I122-14 is more than or equal to 70 Ω B
None of the above conditions are met C



Post-procedure1

c.

None



A

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

B

9.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

C

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-3 - I122-14 Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

NG

8.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-2 - I122-13 Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 5 JUNCTION CONNECTOR)

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)
5.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 5 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-2 - I122-13 Cable disconnected from negative (-) battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

6.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 5 JUNCTION CONNECTOR)
6.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 5 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I17 headup display (meter mirror sub-assembly) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I17)Location & Routing

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

I17-14 (TX+) - I17-15 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I5 combination meter assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I5)Location & Routing

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I5-14 (MSCH) - I5-30 (MSCL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I13 radio receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-5 (CNH1) - I13-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I13 radio receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-5 (CNH1) - I13-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

10.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)
10.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-3 - I122-14 Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)

Pre-procedure1

a.

Disconnect the I5 combination meter assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I5)Location & Routing

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I5-2 (ET) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I5)Location & Routing

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I5-5 (B) - Body ground Always 11 to 14 V
I5-6 (IG+) - Body ground Ignition switch ON 10.5 to 16 V*1
11 to 14 V*2


*1: w/ Stop and Start System

*2: w/o Stop and Start System


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-2 - I122-13 Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

16.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

NG

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)
13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I5 combination meter assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I5)Location & Routing

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I5-14 (MSCH) - I5-30 (MSCL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE)

Pre-procedure1

a.

Disconnect the I17 headup display (meter mirror sub-assembly) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I17)Location & Routing

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

I17-4 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I17)Location & Routing

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

I17-2 (B) - Body ground Always 10.5 to 16 V*1
11 to 14 V*2
I17-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V*1
11 to 14 V*2


*1: w/ Stop and Start System

*2: w/o Stop and Start System


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

15.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 5 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 5 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-1 - I122-12 Cable disconnected from negative (-) battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

16.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

NG

18.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 2 JUNCTION CONNECTOR)
16.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I122 No. 5 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I122)Location & Routing

Click Connector(I122)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 CAN Junction Connector

I122-3 - I122-14 Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

17.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
17.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I13 radio receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-5 (CNH1) - I13-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I17 headup display (meter mirror sub-assembly) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I17)Location & Routing

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

I17-14 (TX+) - I17-15 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR