Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM
RM38G0E _52 Drivetrain _100436 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0468743 AUTOMATIC TRANSMISSION SYSTEM C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P277111  Four Wheel Drive (4WD) Low Switch Circuit Short to Ground  


DESCRIPTION

The ECM detects the signal from the transfer L4 position switch.

This DTC indicates that the transfer L4 position switch remains on.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P277111 Four Wheel Drive (4WD) Low Switch Circuit Short to Ground Transfer L4 position switch remains on while the vehicle is being driven under the following conditions for 1.8 seconds or more (1 trip detection logic):
·

Output shaft speed is between 1000 and 3000 rpm.

·

Transfer position switch is in H4.


·

Short in transfer L4 position switch circuit

·

Transfer system

·

ECM


Comes on DTC stored SAE Code:
P2773

MONITOR DESCRIPTION

The ECM monitors the transfer case L4 position switch to determine when the transfer case L4 gears are engaged. If the transfer case L4 gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL and store the DTC:

·

The L4 switch indicates that the L4 transfer case gears are engaged.

·

The transfer position switch is in H4.

·

The transfer case output shaft speed is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Turn the transfer position switch to H4.

4.
5.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

6.

Input the DTC: P277111.

7.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C328828E18
0.74,3.135 2.75,3.333 2.01,0.198 10 false 4 Wheel Drive Control ECU 0.719,2.948 1.115,3.146 0.396,0.198 10 false B8 5.01,1.979 5.51,2.177 0.5,0.198 10 false L4 2.063,1.979 2.563,2.177 0.5,0.198 10 false L4 5.844,1.135 6.344,1.333 0.5,0.198 10 false 12 V 4.729,1.979 5.063,2.177 0.333,0.198 10 false 35 2.365,1.979 2.604,2.177 0.24,0.198 10 false 3 5.427,2.948 5.927,3.146 0.5,0.198 10 false B2 5.427,3.135 5.927,3.333 0.5,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (L4 TERMINAL VOLTAGE)
a.

Disconnect the 4 wheel drive control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B8)Location & Routing

Click Connector(B8)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

B8-3 (L4) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
a.

Disconnect the 4 wheel drive control ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B8,B2)Location & Routing

Click Connector(B8)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

Click Connector(B2)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B8-3 (L4) or B2-35 (L4) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR