Each mode can be switched with the integration control & panel sub-assembly.
Check each symptom by checking the suspected areas in the table below.
| Result | Proceed to |
|---|---|
| PWR switch system malfunction | A |
| 2ND switch system malfunction | B |
| DAC/CRAWL switch system malfunction | C |
A
B
C
Disconnect the integration control & panel sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I88)Location & Routingewd_type=routing;type=c;code=I88 |
||
| I88-8 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B2)Location & Routingewd_type=routing;type=c;code=B2 |
||
| B2-49 (PWR) - Body ground | PWR switch pushed | 138 Ω or less |
| B2-49 (PWR) - Body ground | PWR switch not pushed | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the integration control & panel sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I88)Location & Routingewd_type=routing;type=c;code=I88 |
||
| I88-8 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B2)Location & Routingewd_type=routing;type=c;code=B2 |
||
| B2-12 (SNWI) - Body ground | 2ND switch pushed | 66 Ω or less |
| B2-12 (SNWI) - Body ground | 2ND switch not pushed | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Operation conditions for downhill assist control.
Transfer position in H4
Shift lever not in P
Front differential lock and rear differential lock not selected
Accelerator pedal and brake pedal not depressed
Driving uphill at a vehicle speed of 30 km/h (19 mph) or lower
Operation conditions for crawl control.
Transfer position in L4
Shift lever not in P or N
Driver side door closed
VSC system normal
2ND start mode off
Parking brake released
Engine started
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the integration control & panel sub-assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I88)Location & Routingewd_type=routing;type=c;code=I88 |
||
| I88-14 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I88)Location & Routingewd_type=routing;type=c;code=I88 |
||
| I88-8 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 2 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B19)Location & Routingewd_type=routing;type=c;code=B19 |
||
| B19-34 (HDCS) - Body ground | DAC/CRAWL switch pushed | Below 100 Ω |
| B19-34 (HDCS) - Body ground | DAC/CRAWL switch not pushed | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Operate the DAC/CRAWL switch to switch to downhill assist control mode.
Operate the MODE SELECT switch.
The target vehicle speed of the meter display changes.
| Proceed to |
|---|
| OK |
| NG |
OK
NG