Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM
RM38G0E _51 Engine / Hybrid System _101047 STOP AND START _0469044 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine stop and start ECU detects whether the engine hood is open or closed based on a signal received from the engine hood courtesy switch built into the hood lock assembly.

The engine stop and start ECU prohibits starting of the engine by stop and start control and changes the mode to "stalled" if the engine hood is opened with the shift lever in D or P while the engine is stopped by stop and start control.

WIRING DIAGRAM

A348169E65
3.542,0.927 3.698,1.125 0.156,0.198 10 false 2 2.031,0.938 2.188,1.135 0.156,0.198 10 false 1 1.875,1.542 2.365,1.844 0.49,0.302 10 false B36 1.875,1.688 3.74,2.24 1.865,0.552 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 5.5,1.583 5.99,1.885 0.49,0.302 10 false B38 5.469,0.948 5.625,1.146 0.156,0.198 10 false 7 5.667,1.052 6.229,1.354 0.563,0.302 10 false BNT1 5.5,1.74 6.563,2.365 1.063,0.625 10 false Engine Stop and Start ECU 2.26,0.938 2.417,1.135 0.156,0.198 10 false E 3.323,0.927 3.479,1.125 0.156,0.198 10 false +

CAUTION / NOTICE / HINT

For wire harness and connector inspection procedures and precautions, refer toGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

PROCEDURE

1.READ VALUE USING GTS (HOOD COURTESY SWITCH)
NOTICE:

Before performing this step, check that the engine hood can be opened by pulling the hood lock control cable.


a.

Enter the following menus: Powertrain / Stop and Start / Data List / Hood Courtesy Switch.

Powertrain > Stop and Start > Data List
Tester Display
Hood Courtesy Switch
50003 392 207

b.

According to the display on the GTS, read the Data List.

OK:
GTS Display Condition Normal Condition
Hood Courtesy Switch Engine hood closed ON
Engine hood open OFF



Result:
Result
OK
NG



OK

CHECK AND ADJUST HOOD LOCK ASSEMBLY FITTING (ADJUST HOOD)

NG

2.INSPECT ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)
2.INSPECT ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)
a.

Inspect the engine hood courtesy switch (hood lock assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>INSPECTION


Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)

NG

REPLACE ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)
a.

Disconnect the engine hood courtesy switch (hood lock assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B36)Location & Routing

Click Connector(B36)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Hood Courtesy Switch (Hood Lock Assembly)

B36-1 (E) - Body ground Always Below 1 Ω



Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY))
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the engine hood courtesy switch (hood lock assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B38,B36)Location & Routing

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

Click Connector(B36)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Hood Courtesy Switch (Hood Lock Assembly)

B38-7 (BNT1) - B36-2 (+) Always Below 1 Ω
B38-7 (BNT1) - Body ground Always 10 kΩ or higher
B36-2 (+) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

CHECK AND ADJUST HOOD LOCK ASSEMBLY FITTING (ADJUST HOOD)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR