Home › Suspension › SUSPENSION CONTROL › ADAPTIVE VARIABLE SUSPENSION SYSTEM
RM38G0E _53 Suspension _100546 SUSPENSION CONTROL _0469072 ADAPTIVE VARIABLE SUSPENSION SYSTEM C

SUSPENSION CONTROL  ADAPTIVE VARIABLE SUSPENSION SYSTEM  C1782  Power Source Voltage Malfunction  


DESCRIPTION

This DTC (C1782) is output if voltage matching the DTC detection condition continues to be supplied to the IGB terminal of the absorber control ECU due to malfunctions in the power source or charging circuits, such as the battery or generator assembly circuits.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
C1782 Power Source Voltage Malfunction While the ignition switch is ON, the voltage at terminal IGB is 10 V or less, or 16 V or higher for 0.5 seconds.
·

AVS-IGR fuse

·

Battery

·

Charging system

·

Wire harness or connector

·

Absorber control ECU


Does not come on No

DTC Detection Conditions: C1781
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition switch is ON ○ ○
Malfunction Status The voltage at terminal IGB is 10 V or less ○ -
The voltage at terminal IGB is 16 V or higher - ○
Detection Time 0.5 seconds 0.5 seconds
Number of Trips 1 trip 1 trip

WIRING DIAGRAM

C346228E15
0.875,0.792 1.885,1 1.01,0.208 10 false from IG Circuit 2.688,0.958 3.396,1.135 0.708,0.177 10 false AVS-IGR 4.667,0.719 4.823,0.917 0.156,0.198 10 false 1 4.656,1.729 4.813,1.927 0.156,0.198 10 false 4 4.833,0.802 5.292,1 0.458,0.198 10 false IGB 4.823,1.813 5.281,2.01 0.458,0.198 10 false GND 4.573,2.354 5.031,2.552 0.458,0.198 10 false Q11 4.75,2.542 6.604,3.083 1.854,0.542 10 false Absorber Control ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

Before replacing the absorber control ECU, perform all of the following:

-

DTC inspection.

*

If no malfunctions are found in other areas, replace the absorber control ECU.



·

After replacing the absorber control ECU with a new one, perform registration of vehicle identification information.

Click hereSuspension>SUSPENSION CONTROL>ADAPTIVE VARIABLE SUSPENSION SYSTEM>TEST MODE PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (IG POWER SOURCE VOLTAGE)
a.

Read the Data List.

Chassis > Adaptive Variable Suspension System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG Power Source Voltage ECU power supply voltage Min.: 0.0 V
Max.: 25.5 V
11 to 14 V (Actual ECU power supply voltage): Ignition switch ON -
Chassis > Adaptive Variable Suspension System > Data List
Tester Display
IG Power Source Voltage
50003 171 33
OK:

The value is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTCS

NG

3.INSPECT BATTERY
2.CHECK FOR DTCS
a.

Clear the DTCs.

Chassis > Adaptive Variable Suspension System > Clear DTCs
50002 171

b.

Turn the ignition switch off.


c.

Check for DTCs.

Chassis > Adaptive Variable Suspension System > Trouble Codes
50001 171

Result:
Result Proceed to
DTC is not output A
DTC is output B



A

B

REPLACE ABSORBER CONTROL ECU

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (IGB TERMINAL)

NG

4.CHECK TERMINAL VOLTAGE (IGB TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the Q11 absorber control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(Q11)Location & Routing

Click Connector(Q11)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Absorber Control ECU

Q11-1 (IGB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the Q11 absorber control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q11)Location & Routing

Click Connector(Q11)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Absorber Control ECU

Q11-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE ABSORBER CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR