w/ Adaptive High Beam System:
The millimeter wave radar sensor assembly communicates with the forward recognition camera and headlight ECU sub-assembly LH via CAN communication.
If a communication error is detected between the forward recognition camera and millimeter wave radar sensor assembly, the millimeter wave radar sensor assembly stores this DTC.
w/o Adaptive High Beam System:
The millimeter wave radar sensor assembly communicates with the forward recognition camera via CAN communication.
If a communication error is detected between the forward recognition camera and millimeter wave radar sensor assembly, the millimeter wave radar sensor assembly stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| U010487 | Lost Communication with Cruise Control Module Missing Message |
Detection condition:
Ignition switch ON
Malfunction status:
Communication malfunction with the forward recognition camera is detected
Malfunction duration:
10 seconds or more |
·
Pre-collision system
·
Forward recognition camera
·
Millimeter wave radar sensor assembly |
Front Radar Sensor | A |
| Pattern | DTC Output Part Name (Display on GTS) |
Suspected Area (Malfunction Status) | ||||||
|---|---|---|---|---|---|---|---|---|
| Millimeter Wave Radar Sensor Assembly | Forward Recognition Camera | Headlight ECU Sub-assembly LH | ||||||
| Front Radar Sensor | Pre-Collision System | Lane Control | Forward Recognition Camera (Front Lighting Control) | Radar Cruise2 | Headlight Control | |||
| U010487 | U023587 | U023587 | U018287 | U023587 | U023587 | U023A87 | ||
|
○: DTC is output -: DTC is not output |
||||||||
| Pattern 1 | ○ | ○ | ○ | ○ | ○ | ○ | ○ | Harness or connector (Open or short) |
| Headlight ECU sub-assembly LH (Internal malfunction) | ||||||||
| Millimeter wave radar sensor assembly (Internal malfunction) | ||||||||
| Forward recognition camera (Internal malfunction) | ||||||||
| Pattern 2 | ○ | - | - | - | - | - | ○ | Forward recognition camera (Internal malfunction) |
| Pattern 3 | ○ | ○ | ○ | - | ○ | ○ | - | Harness or connector (Open) |
| Millimeter wave radar sensor assembly (Internal malfunction) | ||||||||
| Pattern 4 | ○ | - | - | - | - | - | - | Millimeter wave radar sensor assembly (Internal malfunction) |
| Pattern | DTC Output Part Name (Display on GTS) |
Suspected Area (Malfunction Status) | ||||
|---|---|---|---|---|---|---|
| Millimeter Wave Radar Sensor Assembly | Forward Recognition Camera | |||||
| Front Radar Sensor | Pre-Collision System | Lane Control | Forward Recognition Camera (Front Lighting Control) | Radar Cruise2 | ||
| U010487 | U023587 | U023587 | U023587 | U023587 | ||
|
○: DTC is output -: DTC is not output |
||||||
| Pattern 1 | ○ | ○ | ○ | ○ | ○ | Harness or connector (Open or short) |
| Millimeter wave radar sensor assembly (Internal malfunction) | ||||||
| Forward recognition camera (Internal malfunction) | ||||||
| Pattern 2 | ○ | - | - | - | - | Forward recognition camera (Internal malfunction) |
| Millimeter wave radar sensor assembly (Internal malfunction) | ||||||
If the DTCs are output simultaneously, the inspection area can be narrowed down.
w/ Adaptive High Beam System
w/o Adaptive High Beam System
When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.
When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history (RoB). Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.
Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.
Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.
When the forward recognition camera is replaced with a new one, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history (RoB) for each system.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Sequential Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Adaptive High Beam System | A |
| w/o Adaptive High Beam System | B |
A
B
Read each DTC and check the diagnosis pattern using the table below.
| Pattern | DTC Output Part Name (Display on GTS) |
||||||
|---|---|---|---|---|---|---|---|
| Front Radar Sensor | Pre-Collision System | Lane Control | Forward Recognition Camera (Front Lighting Control) | Radar Cruise2 | Headlight Control | ||
| Pattern 1 | U010487 | U023587 | U023587 | U018287 | U023587 | U023587 | U023A87 |
| Pattern 2 | U010487 | - | - | - | - | - | U023A87 |
| Pattern 3 | U010487 | U023587 | U023587 | - | U023587 | U023587 | - |
| Pattern 4 | U010487 | - | - | - | - | - | - |
| Result | Proceed to |
|---|---|
| Pattern 1 | A |
| Pattern 2 | B |
| Pattern 3 | C |
| Pattern 4 | D |
A
B
C
D
Pre-procedure1
Disconnect the cable from the negative (-) battery terminal.
Disconnect the A10 millimeter wave radar sensor assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(A10)Location & Routingewd_type=routing;type=c;code=A10 Click Connector(A10)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Millimeter Wave Radar Sensor Assemblyewd_type=component;type=c;code=A10;pinno=5,6 |
||
| A10-5 (CA1P) - A10-6 (CA1N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Read each DTC and check the diagnosis pattern using the table below.
| Pattern | DTC Output Part Name (Display on GTS) |
||||
|---|---|---|---|---|---|
| Front Radar Sensor | Pre-Collision System | Lane Control | Forward Recognition Camera (Front Lighting Control) | Radar Cruise2 | |
| Pattern 1 | U010487 | U023587 | U023587 | U023587 | U023587 |
| Pattern 2 | U010487 | - | - | - | - |
| Result | Proceed to |
|---|---|
| Pattern 1 | A |
| Pattern 2 | B |
A
B
Pre-procedure1
Disconnect the A10 millimeter wave radar sensor assembly connector.
Procedure1
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
|---|---|---|---|
Click Location & Routing(A10)Location & Routingewd_type=routing;type=c;code=A10 Click Connector(A10)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Millimeter Wave Radar Sensor Assemblyewd_type=component;type=c;code=A10;pinno=5,6 |
|||
| A10-5 (CA1P) - A10-6 (CA1N) | Ignition switch ON | 1 V/DIV., 100 μs./DIV. | Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG