Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › PRE-COLLISION SYSTEM › 2021.04–2022.11
RM38G0E _95 ADAS / AD _100650 ADVANCED DRIVER ASSISTANCE SYSTEM _0469137 PRE-COLLISION SYSTEM C

ADVANCED DRIVER ASSISTANCE SYSTEM  PRE-COLLISION SYSTEM  U023587  Lost Communication with Cruise Control Front Distance Range Sensor Signal Sensor or Center Missing Message  


DESCRIPTION

w/ Adaptive High Beam System:

The forward recognition camera communicates with the millimeter wave radar sensor assembly and headlight ECU sub-assembly LH via CAN communication. If a communication malfunction between the forward recognition camera and millimeter wave radar sensor assembly is detected, DTC U023587 is stored.

w/o Adaptive High Beam System:

The forward recognition camera communicates with the millimeter wave radar sensor assembly via CAN communication. If a communication malfunction between the forward recognition camera and millimeter wave radar sensor assembly is detected, DTC U023587 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U023587 Lost Communication with Cruise Control Front Distance Range Sensor Signal Sensor or Center Missing Message Once 3 seconds elapse after turning the ignition switch to ON, a communication malfunction between the millimeter wave radar sensor assembly continues for approximately 2 seconds or more.
·

Harness or connector

·

Headlight ECU sub-assembly LH (w/ Adaptive High Beam System)

·

Forward recognition camera

·

Millimeter wave radar sensor assembly


Pre-Collision System A

HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


w/ Adaptive High Beam System
Pattern DTC Output Part Name
(Display on GTS)
Suspected Area (Malfunction Status)
Forward Recognition Camera Millimeter Wave Radar Sensor Assembly Headlight ECU Sub-assembly LH
Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control) Radar Cruise2 Front Radar Sensor Headlight Control
U023587 U023587 U018287 U023587 U023587 U010487 U023A87

○: DTC is output

-: DTC is not output

Pattern 1 ○ ○ ○ ○ ○ ○ ○ Harness or connector (Open or short)
Headlight ECU sub-assembly LH (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)
Pattern 2 ○ ○ ○ ○ ○ - - Forward recognition camera (Internal malfunction)
Pattern 3 ○ ○ - ○ ○ ○ - Harness or connector (Open)
Millimeter wave radar sensor assembly (Internal malfunction)
Pattern 4 ○ ○ - ○ ○ - - Millimeter wave radar sensor assembly (Internal malfunction)

w/o Adaptive High Beam System
Pattern DTC Output Part Name
(Display on GTS)
Suspected Area (Malfunction Status)
Forward Recognition Camera Millimeter Wave Radar Sensor Assembly
Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control) Radar Cruise2 Front Radar Sensor
U023587 U023587 U023587 U023587 U010487

○: DTC is output

-: DTC is not output

Pattern 1 ○ ○ ○ ○ ○ Harness or connector (Open or short)
Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)
Pattern 2 ○ ○ ○ ○ - Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)

WIRING DIAGRAM

w/ Adaptive High Beam System


C424986E04
0.302,1.24 0.76,1.438 0.458,0.198 10 false B4 0.302,1.406 2.896,1.885 2.594,0.479 10 false Headlight ECU Sub-assembly LH 1.104,0.448 1.563,0.646 0.458,0.198 10 false LCH 1.125,0.938 1.583,1.135 0.458,0.198 10 false LCL 1.51,0.333 1.823,0.531 0.313,0.198 10 false 22 1.51,0.802 1.823,1 0.313,0.198 10 false 21 5.229,0.813 5.542,1.01 0.313,0.198 10 false 12 5.292,0.333 5.448,0.531 0.156,0.198 10 false 6 5.292,2.76 5.448,2.958 0.156,0.198 10 false 6 5.292,2.292 5.448,2.49 0.156,0.198 10 false 5 5.521,0.333 6.135,0.531 0.615,0.198 10 false CANH 5.521,1.031 6.135,1.229 0.615,0.198 10 false CANL 5.521,2.281 6.135,2.479 0.615,0.198 10 false CA1P 5.521,2.99 6.135,3.188 0.615,0.198 10 false CA1N 4.99,1.188 5.448,1.385 0.458,0.198 10 false d20 4.427,3.135 4.885,3.333 0.458,0.198 10 false A10 4.99,1.365 7.021,1.771 2.031,0.406 10 false Forward Recognition Camera 4.417,3.313 7.125,3.688 2.708,0.375 10 false Millimeter Wave Radar Sensor Assembly


w/o Adaptive High Beam System


B330403E34
0.75,1.875 3.042,2.354 2.292,0.479 10 false Forward Recognition Camera 4.823,1.854 6.219,2.615 1.396,0.76 10 false Millimeter Wave Radar Sensor Assembly 0.75,1.688 1.115,1.885 0.365,0.198 10 false d20 4.823,1.688 5.24,1.917 0.417,0.229 10 false A10 1.604,0.792 2.219,0.99 0.615,0.198 10 false CANH 1.615,1.469 2.229,1.667 0.615,0.198 10 false CANL 5.115,0.771 5.729,0.969 0.615,0.198 10 false CA1P 5.125,1.479 5.74,1.677 0.615,0.198 10 false CA1N 2.083,0.781 2.24,0.979 0.156,0.198 10 false 6 2.073,1.25 2.271,1.448 0.198,0.198 10 false 12 4.948,0.771 5.104,0.969 0.156,0.198 10 false 5 4.948,1.24 5.104,1.438 0.156,0.198 10 false 6


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history (RoB). Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT


·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history (RoB) for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT


·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

w/ Adaptive High Beam System:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>REGISTRATION

·

w/ Adaptive High Beam System:

When replacing the headlight ECU sub-assembly LH, always replace it with a new one. If a headlight ECU sub-assembly LH which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Adaptive High Beam System A
w/o Adaptive High Beam System B



A

2.CHECK FOR DTCs

B

7.CHECK FOR DTCs
2.CHECK FOR DTCs
a.

Read each DTC and check the diagnosis pattern using the table below.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Chassis > Lane Control > Trouble Codes
50001 418
Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433
Powertrain > Radar Cruise2 > Trouble Codes
50001 426
Body Electrical > Front Radar Sensor > Trouble Codes
50001 429
Body Electrical > Headlight Control > Trouble Codes
50001 462
Pattern DTC Output Part Name
(Display on GTS)
Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control) Radar Cruise2 Front Radar Sensor Headlight Control
Pattern 1 U023587 U023587 U018287 U023587 U023587 U010487 U023A87
Pattern 2 U023587 U023587 U018287 U023587 U023587 - -
Pattern 3 U023587 U023587 - U023587 U023587 U010487 -
Pattern 4 U023587 U023587 - U023587 U023587 - -


Result:
Result Proceed to
Pattern 1 A
Pattern 2 B
Pattern 3 C
Pattern 4 D



A

3.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

B

REPLACE FORWARD RECOGNITION CAMERA

C

6.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

D

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

3.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


b.

Clear the DTCs.

Body Electrical > Pre-Collision System > Clear DTCs
50002 432

Procedure1

c.

Check for DTCs.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Result:
Result Proceed to
DTC U023587 is not output A
DTC U023587 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

4.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
4.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY

Pre-procedure1

a.

Connect the B4 headlight ECU sub-assembly LH connector.


b.

Disconnect the A10 millimeter wave radar sensor assembly connector.


c.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Procedure1

d.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
DTC U023A87 is not output A
DTC U023A87 is output B



Post-procedure1

e.

None



A

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

5.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)
5.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)

Pre-procedure1

a.

Connect the A10 millimeter wave radar sensor assembly connector.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the d20 forward recognition camera connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d20)Location & Routing

Click Connector(d20)Body>No. 1 Roof Wire>Forward Recognition Camera

d20-6 (CANH) - d20-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
d20-6 (CANH) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
d20-12 (CANL) - Body ground
d20-6 (CANH) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
d20-12 (CANL) - +B


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A10 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A10)Location & Routing

Click Connector(A10)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Millimeter Wave Radar Sensor Assembly

A10-5 (CA1P) - A10-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK FOR DTCs
a.

Read each DTC and check the diagnosis pattern using the table below.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Chassis > Lane Control > Trouble Codes
50001 418
Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433
Powertrain > Radar Cruise2 > Trouble Codes
50001 426
Body Electrical > Front Radar Sensor > Trouble Codes
50001 429
Pattern DTC Output Part Name
(Display on GTS)
Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control) Radar Cruise2 Front Radar Sensor
Pattern 1 U023587 U023587 U023587 U023587 U010487
Pattern 2 U023587 U023587 U023587 U023587 -


Result:
Result Proceed to
Pattern 1 A
Pattern 2 B



A

8.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)

B

10.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
8.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the d20 forward recognition camera connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d20)Location & Routing

Click Connector(d20)Body>No. 1 Roof Wire>Forward Recognition Camera

d20-6 (CANH) - d20-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
d20-6 (CANH) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
d20-12 (CANL) - Body ground
d20-6 (CANH) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
d20-12 (CANL) - +B


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

9.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
9.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

Pre-procedure1

a.

Connect the d20 forward recognition camera connector.


b.

Disconnect the A10 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A10)Location & Routing

Click Connector(A10)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Millimeter Wave Radar Sensor Assembly

A10-5 (CA1P) - A10-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A10-5 (CA1P) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A10-6 (CA1N) - Body ground
A10-5 (CA1P) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A10-6 (CA1N) - +B


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY

Pre-procedure1

a.

Disconnect the d20 forward recognition camera connector.


Procedure1

b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(d20)Location & Routing

Click Connector(d20)Body>No. 1 Roof Wire>Forward Recognition Camera

d20-6 (CANH) - d20-12 (CANL) Ignition switch ON 1V/DIV., 100μs./DIV. Pulse generation


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY