Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P001313  Camshaft Position "B" - Actuator Bank 1 Circuit Open  P002313  Camshaft Position "B" - Actuator Bank 2 Circuit Open  


DESCRIPTION

·

These DTCs are designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the duty-cycle for the camshaft timing oil control valve is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

·

The VVT (Variable Valve Timing) system adjusts the exhaust valve timing to improve driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The camshaft timing oil control valve is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time of the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.


A192077E14
4.483,0.815 5.318,1.026 0.834,0.211 10 VVT Sensor 4.483,1.325 6.234,1.485 1.751,0.161 10 Crankshaft Position Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 3.765,3.922 2.166,0.174 10 Camshaft Timing Oil Control Valve 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty-cycle 4.483,1.827 5.818,1.981 1.334,0.154 10 Mass Air Flow Meter 4.483,2.854 6.799,3.042 2.316,0.188 10 Engine Coolant Temperature Sensor 4.483,2.344 6.049,2.511 1.566,0.167 10 Throttle Position Sensor 4.483,3.353 5.929,3.506 1.446,0.154 10 Vehicle Speed Sensor 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 4.885,4.400 1.225,0.184 10 Camshaft Actuator 3.883,4.917 5.067,5.101 1.184,0.184 10 Exhaust Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P001313 Camshaft Position "B" - Actuator Bank 1 Circuit Open Open or short in the camshaft timing oil control valve (for exhaust side of bank 1) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve (for exhaust side of bank 1) circuit

·

Camshaft timing oil control valve assembly (for exhaust side of bank 1)

·

ECM


Comes on SAE: P0013
P002313 Camshaft Position "B" - Actuator Bank 2 Circuit Open Open or short in the camshaft timing oil control valve (for exhaust side of bank 2) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve (for exhaust side of bank 2) circuit

·

Camshaft timing oil control valve assembly (for exhaust side of bank 2)

·

ECM


Comes on SAE: P0023

MONITOR DESCRIPTION

These DTCs are designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the duty-cycle for the camshaft timing oil control valve is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P001313 or P002313.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A160561E21
0.573,3.719 1.333,3.896 0.76,0.177 10 false C83 0.573,3.885 2.771,4.365 2.198,0.479 10 false Camshaft Timing Oil Control Valve (for Exhaust Side of Bank 2) 0.573,1.906 2.771,2.302 2.198,0.396 10 false Camshaft Timing Oil Control Valve (for Exhaust Side of Bank 1) 1.448,0.615 1.615,0.781 0.167,0.167 10 false 1 1.469,1.354 1.635,1.521 0.167,0.167 10 false 2 0.573,1.76 1.021,1.906 0.448,0.146 10 false C82 1.448,2.573 1.615,2.74 0.167,0.167 10 false 1 1.458,3.323 1.625,3.49 0.167,0.167 10 false 2 5.156,0.615 5.385,0.76 0.229,0.146 10 false 2 5.427,0.615 5.917,0.917 0.49,0.302 10 false OE1+ 5.167,1.344 5.396,1.49 0.229,0.146 10 false 1 5.438,1.344 5.885,1.604 0.448,0.26 10 false OE1- 5.115,2.583 5.344,2.729 0.229,0.146 10 false 24 5.417,2.583 5.885,2.844 0.469,0.26 10 false OE2+ 5.125,3.313 5.354,3.458 0.229,0.146 10 false 47 5.438,3.313 5.906,3.594 0.469,0.281 10 false OE2- 5.594,4.219 6.75,4.438 1.156,0.219 10 false C92 5.594,4.375 6.094,4.573 0.5,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

If DTC P001313 is output, check the bank 1 VVT system for the exhaust camshaft circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

If DTC P002313 is output, check the bank 2 VVT system for the exhaust camshaft circuit.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (DTC P001313 OR P002313)
a.

Turn the ignition switch to ON.


b.

Clear the DTC after recording the freeze frame data and DTC.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON and wait 5 seconds.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P001313 or P002313 is output A
DTCs are not output B




A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE (FOR EXHAUST CAMSHAFT)

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE (FOR EXHAUST CAMSHAFT)
a.

Inspect the camshaft timing oil control valve (for Exhaust Side)

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)
a.

Disconnect the camshaft timing oil control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C82,C92,C83)Location & Routing

Click Connector(C82)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Timing Oil Control Solenoid Assembly RH (Bank 1 Exhaust Side)

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C83)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Timing Oil Control Solenoid Assembly LH (Bank 2 Exhaust Side)

C82-1 - C92-2 (OE1+) Always Below 1 Ω
C82-2 - C92-1 (OE1-) Always Below 1 Ω
C83-1 - C92-24 (OE2+) Always Below 1 Ω
C83-2 - C92-47 (OE2-) Always Below 1 Ω
C82-1 or C92-2 (OE1+) - Body ground Always 10 kΩ or higher
C82-2 or C92-1 (OE1-) - Body ground Always 10 kΩ or higher
C83-1 or C92-24 (OE2+) - Body ground Always 10 kΩ or higher
C83-2 or C92-47 (OE2-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR