Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P144A12  AIR System Heater "A" Control Circuit High Circuit Short to Battery  P144A14  AIR System Heater "A" Control Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

The ECM operates the air pump heater relay which causes the air pump heater to operate.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P144A12 AIR System Heater "A" Control Circuit High Circuit Short to Battery Open or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
·

Open or short in AIR PMP HTR relay circuit

·

AIR PMP HTR relay

·

ECM


Comes on SAE: P144D
P144A14 AIR System Heater "A" Control Circuit Low Circuit Short to Ground or Open Open or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
·

Open or short in AIR PMP HTR relay circuit

·

AIR PMP HTR relay

·

ECM


Comes on SAE: P144C

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait for 10 seconds.

7.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Air Pump Heater.

8.

Activate the air pump heater for 10 seconds or more.

HINT:
·

The Active Test activates the air pump heater for up to 60 seconds.

·

To protect the air pump heater, do not perform this test more than 4 times in a row.



9.

Enter the following menus: Powertrain / Engine / DTC.

10.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P144A12 or P144A14.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT RELAY (AIR PMP HTR)

Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (AIR PMP HTR RELAY POWER SOURCE)

NG

REPLACE RELAY (AIR PMP HTR)

2.CHECK TERMINAL VOLTAGE (AIR PMP HTR RELAY POWER SOURCE)
a.

Remove the AIR PMP HTR relay.


b.
A488680C01
0.104,0.104 0.417,0.26 0.313,0.156 10 false *1 0.896,1.854 1.208,2.01 0.313,0.156 10 false *a
*1 Engine Room Relay Block No. 2
*a AIR PMP HTR Relay Terminal


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (AIR PMP HTR relay) - Body ground Always 11 to 14 V
5 (AIR PMP HTR relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - AIR PMP HTR RELAY)

NG

HARNESS OR CONNECTOR (AIR PMP HTR RELAY - BATTERY)

3.CHECK HARNESS AND CONNECTOR (ECM - AIR PMP HTR RELAY)
a.

Remove the AIR PMP HTR relay.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B2)Location & Routing

Click Connector(B2)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

1 (AIR PMP HTR relay) - B2-14 (HAI1) Always Below 1 Ω
1 (AIR PMP HTR relay) or B2-14 (HAI1) - Body ground Always 10 kΩ or higher



d.

Reinstall the AIR PMP HTR relay.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR