The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.
The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P001013 | A Camshaft Position Actuator Bank 1 Circuit Open | Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 1) circuit (1 trip detection logic). |
·
Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 1) circuit
·
Camshaft timing oil control valve assembly (for intake camshaft of bank 1)
·
ECM |
Comes on | SAE: P0010 |
| P002013 | Camshaft Position "A" Actuator Bank 2 Circuit Open | Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 2) circuit (1 trip detection logic). |
·
Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 2) circuit
·
Camshaft timing oil control valve assembly (for intake camshaft of bank 2)
·
ECM |
Comes on | SAE: P0020 |
These DTCs are designed to detect an open or short in the camshaft timing oil control valve assembly (for intake camshaft) circuit. If the camshaft timing oil control valve assembly duty-cycle is excessively high or low while the ignition switch to ON or the engine is running, the ECM will illuminate the MIL and store a DTC.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Wait 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P001013 or P002013.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
| N/A |
·
Unable to perform DTC judgment
·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
If DTC P001013 is output, check the VVT system (for intake camshaft of bank 1) circuit.
If DTC P002013 is output, check the VVT system (for intake camshaft of bank 2) circuit.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Turn the ignition switch to ON.
Clear the DTC after recording the freeze frame data and DTC.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and wait 5 seconds.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P001013 or P002013 is output | A |
| DTCs are not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Inspect the camshaft timing oil control valve assembly (for intake camshaft).
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the camshaft timing oil control valve assembly (for intake camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C80,C92,C81)Location & Routingewd_type=routing;type=c,c,c;code=C80,C92,C81 |
||
| C80-1 - C92-6 (OC1+) | Always | Below 1 Ω |
| C80-2 - C92-5 (OC1-) | Always | Below 1 Ω |
| C81-1 - C92-4 (OC2+) | Always | Below 1 Ω |
| C81-2 - C92-3 (OC2-) | Always | Below 1 Ω |
| C80-1 or C92-6 (OC1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C80-2 or C92-5 (OC1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C81-1 or C92-4 (OC2+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C81-2 or C92-3 (OC2-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG