Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P210900  Throttle/Pedal Position Sensor "A" Minimum Stop Performance  


DESCRIPTION

The idle speed is controlled by the Electronic Throttle Control System (ETCS). The ETCS is comprised of a throttle actuator, which operates the throttle valve, and a throttle position sensor, which detects the opening amount of the throttle valve. The ECM controls the throttle actuator to adjust the throttle valve opening amount so that the idle speed is maintained at the target idle speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P210900 Throttle/Pedal Position Sensor "A" Minimum Stop Performance The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount during idle is within the normal range (up to 1.5 times the normal amount) (5 trip detection logic). Throttle with throttle position sensor body assembly Does not come on SAE: P2109

HINT:
·

The ISC learned value is the calculated intake air amount corresponding to the throttle opening amount necessary to maintain the idling speed.

·

This malfunction is only detected once per trip. After it has been detected once, the system will not monitor for the malfunction for the rest of the trip.

·

The system uses the throttle with throttle position sensor body assembly and mass air flow meter to detect this malfunction.



MONITOR DESCRIPTION

If there are deposits in the throttle valve, a decrease in the ISC flow rate may cause engine stall or unstable idling. Therefore, the necessary ISC flow rate for idling is maintained using the ISC learned value and feedback. The ECM stores this DTC if the ISC learned value approaches its limit. The ECM begins monitoring for the DTC detection conditions when the following preconditions are met:

1) The mass air flow meter sub-assembly is normal.

2) Atmospheric pressure is 85 kPa(abs) [637.6 mmHg(abs)] or higher.

3) The vehicle has been driven at a speed of 30 km/h (18.7 mph) or more at least once.

4) The engine coolant temperature is 45°C (113°F) or less at engine start, the engine is warmed up and conditions for ISC learning are met, or the ignition switch has been turned to ON (including when the engine is running) for 1 hour or more, the engine is warmed up and conditions for ISC learning are met.

CAUTION / NOTICE / HINT

HINT:
·

Since a pending DTC is not stored for this DTC, it takes time to confirm whether the malfunction has been successfully repaired by checking for this DTC. When confirming whether the malfunction has been successfully repaired, compare "Throttle Air Flow F/B Value" recorded in the freeze frame data with "Throttle Air Flow F/B Value" in the Data List after repairs have been made to save time.

·

Read freeze frame data using the GTS. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P210900)
a.

Turn the ignition switch to ON.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P210900 is output A
DTC P210900 and other DTCs are output B


HINT:

If any DTCs other than P210900 are output, troubleshoot those DTCs first.




A

2.READ FREEZE FRAME DATA

B

2.READ FREEZE FRAME DATA
a.

Turn the ignition switch to ON.


b.

Using the GTS, check "Throttle Air Flow F/B Value" in the freeze frame data.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA

HINT:

Be sure to confirm "Throttle Air Flow F/B Value" in the freeze frame data as it is used when confirming whether the malfunction has been successfully repaired.



Result:
Proceed to
NEXT



NEXT

3.REMOVE FOREIGN MATTER (CLEAN THROTTLE WITH THROTTLE POSITION SENSOR BODY ASSEMBLY)
3.REMOVE FOREIGN MATTER (CLEAN THROTTLE WITH THROTTLE POSITION SENSOR BODY ASSEMBLY)
a.

Clean off any deposits from the inside of the throttle with throttle position sensor body assembly.

A213929C10
1.958,1.323 2.354,1.594 true 1.969,1.146 2.354,1.146 true 0.781,2.479 1.229,2.375 true 1.729,3.625 1.521,3.073 true 1.031,0.573 1.604,0.688 true 0.771,3.073 1.385,2.729 true 0.271,0.344 0.583,0.5 0.313,0.156 10 false *1 0.854,0.51 1.167,0.667 0.313,0.156 10 false *2 2.406,1.542 2.656,1.823 0.25,0.281 10 false *e 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.688,0.177 2,0.333 0.313,0.156 10 false *b 1.688,1.927 2,2.083 0.313,0.156 10 false *c 4.771,0.917 5.083,1.073 0.313,0.156 10 false *d 0.583,2.417 0.896,2.573 0.313,0.156 10 false *2 1.667,3.625 2,3.802 0.333,0.177 10 false *e 0.594,3.031 0.906,3.188 0.313,0.156 10 false *3 2.385,1.083 2.698,1.24 0.313,0.156 10 false *3
*1 Throttle with Throttle Position Sensor Body Assembly *2 Bore
*3 Valve - -
*a Reference *b Throttle with Throttle Position Sensor Body Assembly Cross-section Diagram
*c When valve fully opened *d Do not directly apply cleaner
*e Deposits - -


i.

Push open the throttle valve and wipe off any carbon from the valve and bore using a cloth soaked in non-residue solvent.

NOTICE:
·

Make sure that the cloth or your fingers do not get caught in the valve.

·

Make sure that foreign matter does not enter the throttle valve.

·

Do not directly apply non-residue solvent to the throttle with throttle position sensor body assembly or wash the throttle with throttle position sensor body assembly. Cleaning solvent may leak into the motor from the shaft and cause problems such as rust or valve movement problems.

·

If there is coating material on the edge of the valve, be careful not to remove it.

·

Push the throttle valve open gently with your finger and check that the throttle valve moves smoothly.



HINT:
·

If the throttle valve does not open smoothly, replace the throttle with throttle position sensor body assembly.

·

The illustration is for reference only, actual parts may differ.





Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (THROTTLE AIR FLOW F/B VALUE)
4.READ VALUE USING GTS (THROTTLE AIR FLOW F/B VALUE)
a.

Perform "Inspection After Repair" after cleaning the throttle with throttle position sensor body assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


b.

Turn the ignition switch to ON.


c.

Read the value.

Powertrain > Engine > Data List
Tester Display
Throttle Air Flow F/B Value
50003 372 120
OK:

The value is half of "Throttle Air Flow F/B Value" recorded in the freeze frame data or less.


HINT:

Perform "Inspection After Repair" after replacing the throttle with throttle position sensor body assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY