Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P21201C  Throttle/Pedal Position Sensor/Switch "D" Circuit Voltage Out of Range  P212099  Throttle/Pedal Position Sensor/Switch "D" Exceeded Learning Limit  


DESCRIPTION

Refer to DTC P212012.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P212012

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P21201C Throttle/Pedal Position Sensor/Switch "D" Circuit Voltage Out of Range Difference between VPA and VPA2 is greater than or equal to the specified value for 0.5 seconds. (1 trip detection logic)
·

Accelerator pedal (with sensor) rod assembly

·

ECM


Comes on SAE: P2121
P212099 Throttle/Pedal Position Sensor/Switch "D" Exceeded Learning Limit Difference between VPA and VPA2 is less than 0.4 V, or higher than 1.2 V (learned value of accelerator off position) for 0.5 seconds. (1 trip detection logic)
·

Accelerator pedal (with sensor) rod assembly

·

ECM


Comes on SAE: P2121

MONITOR DESCRIPTION

The accelerator pedal position sensor is built into the accelerator pedal. The accelerator pedal position sensor has 2 sensor elements and 2 signal outputs: VPA and VPA2. VPA is used to detect the actual accelerator pedal angle (used for engine control) and VPA2 is used to detect malfunctions in VPA. When the difference between the output voltages of VPA and VPA2 deviates from the standard, the ECM determines that the accelerator pedal position sensor is malfunctioning. The ECM then illuminates the MIL and stores a DTC.

CONFIRMATION DRIVING PATTERN

A256657E12
3.635,2.01 2.771,1.302 2.771,1.302 2.927,1.302 false 4.729,2.448 5.115,1.802 5.115,1.802 5.26,1.802 false 2.208,2.448 2.438,2.104 2.438,2.104 2.542,2.104 false 0.125,0.083 1.75,0.323 1.625,0.24 10 Accelerator Pedal State 0.896,0.458 1.698,0.708 0.802,0.25 10 Depressed 0.99,0.906 1.708,1.146 0.719,0.24 10 Released 0.427,2.406 1.667,2.667 1.24,0.26 10 Ignition Switch ON 2.115,2.49 2.333,2.75 0.219,0.26 10 [A] 4.396,3.406 4.646,3.635 0.25,0.229 10 [C] 5.313,1.729 6.063,1.979 0.75,0.25 10 Released 2.375,3.052 3.167,3.333 0.792,0.281 10 5 seconds 2.99,1.219 3.823,1.469 0.833,0.25 10 Depressed 3.865,3.042 4.125,3.26 0.26,0.219 10 [B] 2.594,2.031 3.25,2.25 0.656,0.219 10 Released

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Wait for 5 seconds after turning the ignition switch to ON.

7.

Operate the accelerator pedal in accordance with the following procedure [B].

(a)

Enter the following menus: Powertrain / Engine / Data List / All Data / Accelerator Position Sensor No.1 Voltage %, and Accelerator Position Sensor No.2 Voltage %.

(b)

Slowly depress the accelerator pedal until Accelerator Position Sensor No.1 Voltage % is approximately 30% and Accelerator Position Sensor No.2 Voltage % is approximately 46%, then slowly release the accelerator pedal.


8.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P21201C or P212099.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.




FAIL-SAFE

The accelerator pedal position sensor has 2 (main and sub) sensor circuits. If the ECM detects an abnormal signal voltage difference between the 2 sensor circuits it switches to fail-safe mode. If the either of the 2 sensor circuits malfunctions, the ECM limits the engine output. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. In this case, the throttle valve remains closed as if the engine is idling.

If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to normal.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P21201C OR P212099)
a.

Turn the ignition switch to ON.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P21201C or P212099 is output A
DTC P21201C or P212099 and other DTCs are output B


HINT:

If any DTCs other than P21201C or P212099 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR VOLTAGE)

B

2.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR VOLTAGE)
A208621C06
0.667,1.75 1.448,2.177 0.781,0.427 10 *a 2.615,1.75 3.177,2.177 0.563,0.427 10 *b
*a Fully Depressed
*b Fully Released


a.

Turn the ignition switch to ON.


b.

Read the values displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Accelerator Position Sensor No.1 Voltage
Accelerator Position Sensor No.2 Voltage
50003 372 87,88
Standard Voltage:
Accelerator Pedal Operation Accelerator Position Sensor No.1 Voltage Accelerator Position Sensor No.2 Voltage
Fully Released 0.5 to 1.1 V 1.2 to 2.0 V
Fully Depressed 2.6 to 4.5 V 3.4 to 4.75 V



Result:
Proceed to
OK
NG



OK

NG

3.REPLACE ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY
3.REPLACE ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY
a.

Replace the accelerator pedal (with sensor) rod assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P21201C OR P212099)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P21201C OR P212099)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P21201C or P212099 is output A
DTCs are not output B




A

B

END