Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P223711  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Ground  P223712  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Battery  P223713  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Open  P223716  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Below Threshold  P223717  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Above Threshold  P22371B  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Resistance Above Threshold  P224011  A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Short to Ground  P224012  A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Short to Battery  P224013  A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Open  P224016  A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Voltage Below Threshold  P224017  A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Voltage Above Threshold  P22401B  A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Resistance Above Threshold  P225111  O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Ground  P225112  O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Battery  P225411  O2 Sensor Negative Current Control Bank 2 Sensor 1 Circuit Short to Ground  P225412  O2 Sensor Negative Current Control Bank 2 Sensor 1 Circuit Short to Battery  


DESCRIPTION

HINT:

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.


The air fuel ratio sensor generates voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and integrated with a heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), current flows to the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through alumina, therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A306366E01
1.49,2.167 1,1.75 1,1.75 0.833,1.75 false 1.656,2.094 1.823,1.844 1.823,1.844 1.906,1.844 false 2.938,1.177 3.104,0.396 3.104,0.396 3.188,0.396 false 3.083,1.198 3.25,0.917 3.25,0.917 3.333,0.917 false 3.156,1.198 3.333,1.167 3.333,1.167 3.417,1.167 false 2.875,1.667 3.406,1.5 3.406,1.5 2.99,1.667 false 3.042,1.75 3.417,2.083 3.417,2.083 3.5,2.083 false 0.281,1.656 1.354,1.854 1.073,0.198 10 false Element 0.135,2.385 1.208,2.583 1.073,0.198 10 false Exhaust Gas 1.083,2.49 1.417,2.667 0.333,0.177 10 false A 1.802,2.49 2.135,2.667 0.333,0.177 10 false A 1.948,1.76 2.333,1.917 0.385,0.156 10 false Cover 3.26,0.219 4.417,0.583 1.156,0.365 10 false Solid Electrolyte (Zirconia Element) 3.385,0.833 4.052,0.99 0.667,0.156 10 false Alumina 3.458,1.083 4.125,1.24 0.667,0.156 10 false Heater 3.448,1.417 4.698,1.667 1.25,0.25 10 false Platinum Electrode 3.542,2 4.792,2.25 1.25,0.25 10 false Atmospheric Air 2.531,2.333 3.865,2.5 1.333,0.167 10 false A-A Cross Section 5.323,0.167 6.823,0.5 1.5,0.333 10 false ECM Monitored Air Fuel Ratio Sensor Voltage 5.563,2.25 6.896,2.417 1.333,0.167 10 false Air Fuel Ratio

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P223711 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Ground The A1A+ voltage is 0.5 V or less for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on SAE: P2238
P223712 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Battery The A1A+ voltage is higher than 4.5 V for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on SAE: P2239
P223713 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Open An open or ground short in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on SAE: P2237
P223716 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Below Threshold Difference between terminals A1A+ and A1A- is 0.1 V or less for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on SAE: P2238
P223717 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Above Threshold Difference between terminals A1A+ and A1A- is higher than 0.8 V for 5 seconds or more (2trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on SAE: P2239
P22371B A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Resistance Above Threshold The air fuel ratio sensor admittance is less than 0.0054 1/Ω (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on SAE: P2238
P224011 A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Short to Ground The A2A+ voltage is 0.5 V or less for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on SAE: P2241
P224012 A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Short to Battery The A2A+ voltage is higher than 4.5 V for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on SAE: P2242
P224013 A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Open An open or ground short in the circuit between terminals A2A+ and A2A- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on SAE: P2240
P224016 A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Voltage Below Threshold Difference between terminals A2A+ and A2A- is 0.1 V or less for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on SAE: P2241
P224017 A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Voltage Above Threshold Difference between terminals A2A+ and A2A- is higher than 0.8 V for 5 seconds or more (2trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on SAE: P2242
P22401B A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Resistance Above Threshold The air fuel ratio sensor admittance is less than 0.0054 1/Ω (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on SAE: P2241
P225111 O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Ground The A1A- voltage is 0.5 V or less for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on SAE: P2252
P225112 O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Battery The A1A- voltage is higher than 4.5 V for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on SAE: P2253
P225411 O2 Sensor Negative Current Control Bank 2 Sensor 1 Circuit Short to Ground The A2A- voltage is 0.5 V or less for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on SAE: P2255
P225412 O2 Sensor Negative Current Control Bank 2 Sensor 1 Circuit Short to Battery The A2A- voltage is higher than 4.5 V for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on SAE: P2256

MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the air fuel ratio sensor circuit, or if the air fuel ratio sensor output drops. To detect these problems, the voltage of the air fuel ratio sensor is monitored when turning the ignition switch to ON, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the air fuel ratio sensor is between 0.5 V and 4.5 V, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM determines that there is a malfunction in the air fuel ratio sensor. If the same malfunction is detected in the next driving cycle, the ECM will illuminate the MIL and store a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait 5 minutes.

7.

Enter the following menus: Powertrain / Engine / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P223711, P223712, P223713, P223716, P223717, P22371B, P224011, P224012, P224013, P224016, P224017, P22401B, P225111, P225112, P225411 or P225412.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.




WIRING DIAGRAM

A488683E01
0.75,0.667 1.333,0.833 0.583,0.167 10 false A/F HTR 5.385,1.167 5.969,1.333 0.583,0.167 10 false A/F 1.625,1.052 2.635,1.271 1.01,0.219 10 false EFI MAIN NO.1 2.813,1.583 3.854,1.802 1.042,0.219 10 false EFI MAIN NO.1 4.094,1.063 4.865,1.292 0.771,0.229 10 false EFI-B NO.2 2.854,0.792 3.01,0.99 0.156,0.198 10 false 5 3.552,0.792 3.708,0.99 0.156,0.198 10 false 3 2.854,1.198 3.01,1.396 0.156,0.198 10 false 2 3.552,1.188 3.708,1.385 0.156,0.198 10 false 1 5.135,0.396 5.292,0.594 0.156,0.198 10 false 5 5.135,0.802 5.292,1 0.156,0.198 10 false 2 5.802,0.813 5.958,1.01 0.156,0.198 10 false 1 5.813,0.396 5.969,0.594 0.156,0.198 10 false 3 0.385,5.698 1.385,5.948 1,0.25 10 false SUB R/B-NO.1 0.594,6.969 1.083,7.167 0.49,0.198 10 false Battery 1.927,5.052 2.083,5.25 0.156,0.198 10 false 2 1.927,2.917 2.083,3.115 0.156,0.198 10 false 2 3.177,5.052 3.333,5.25 0.156,0.198 10 false 1 3.177,2.917 3.333,3.115 0.156,0.198 10 false 1 3.177,3.385 3.333,3.583 0.156,0.198 10 false 3 3.177,5.552 3.333,5.75 0.156,0.198 10 false 3 3.177,3.885 3.333,4.083 0.156,0.198 10 false 4 3.167,6 3.323,6.198 0.156,0.198 10 false 4 4.177,3.385 4.333,3.583 0.156,0.198 10 false * 4.177,5.521 4.333,5.719 0.156,0.198 10 false * 1.427,7.333 2.167,7.5 0.74,0.167 10 false *: Shielded 5.417,2.833 5.667,3 0.25,0.167 10 false 22 5.365,3.031 5.698,3.198 0.333,0.167 10 false C92 5.417,3.302 5.635,3.49 0.219,0.188 10 false 98 5.365,3.51 5.698,3.677 0.333,0.167 10 false C92 5.427,3.781 5.615,3.969 0.188,0.188 10 false 97 5.417,4.969 5.667,5.167 0.25,0.198 10 false 45 5.375,5.448 5.677,5.646 0.302,0.198 10 false 121 5.375,5.917 5.635,6.104 0.26,0.188 10 false 120 5.438,6.802 5.688,7 0.25,0.198 10 false 6 5.396,7 5.729,7.198 0.333,0.198 10 false B2 5.75,6.99 6.167,7.156 0.417,0.167 10 false MREL 5.76,6.031 6.167,6.198 0.406,0.167 10 false A2A- 5.75,5.552 6.167,5.75 0.417,0.198 10 false A2A+ 5.76,5.052 6.167,5.25 0.406,0.198 10 false HA2A 5.75,3.896 6.167,4.063 0.417,0.167 10 false A1A- 5.76,3.385 6.167,3.583 0.406,0.198 10 false A1A+ 5.76,2.917 6.25,3.115 0.49,0.198 10 false HA1A 6.094,7.417 6.427,7.615 0.333,0.198 10 false ECM 1.781,4.198 2.115,4.396 0.333,0.198 10 false C87 1.781,4.365 4.281,4.531 2.5,0.167 10 false Air Fuel Ratio Sensor (Bank 1 Sensor 1) 1.781,6.313 2.219,6.5 0.438,0.188 10 false C88 1.781,6.479 4.281,6.646 2.5,0.167 10 false Air Fuel Ratio Sensor (Bank 2 Sensor 1) 5.365,3.99 5.698,4.156 0.333,0.167 10 false C92 5.365,5.177 5.698,5.344 0.333,0.167 10 false C92 5.365,5.656 5.698,5.823 0.333,0.167 10 false C92 5.365,6.135 5.698,6.302 0.333,0.167 10 false C92 2.719,2.917 3.208,3.115 0.49,0.198 10 false HA1A 2.146,2.917 2.635,3.115 0.49,0.198 10 false +B 2.146,5.063 2.635,5.26 0.49,0.198 10 false +B 2.719,5.052 3.125,5.25 0.406,0.198 10 false HA2A 2.729,3.385 3.135,3.583 0.406,0.198 10 false A1A+ 2.75,3.875 3.167,4.042 0.417,0.167 10 false A1A- 2.719,5.531 3.135,5.729 0.417,0.198 10 false A2A+ 2.76,6.021 3.167,6.188 0.406,0.167 10 false A2A-

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1 and A/F (O2) Sensor Voltage B2S1].

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C87,C92,C88)Location & Routing

Click Connector(C87)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 1 Sensor 1)

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C88)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 2 Sensor 1)

C87-1 (HA1A) - C92-22 (HA1A) Always Below 1 Ω
C87-3 (A1A+) - C92-98 (A1A+) Always Below 1 Ω
C87-4 (A1A-) - C92-97 (A1A-) Always Below 1 Ω
C88-1 (HA2A) - C92-45 (HA2A) Always Below 1 Ω
C88-3 (A2A+) - C92-121 (A2A+) Always Below 1 Ω
C88-4 (A2A-) - C92-120 (A2A-) Always Below 1 Ω
C87-1 (HA1A) or C92-22 (HA1A) - Body ground and other terminals Always 10 kΩ or higher
C87-3 (A1A+) or C92-98 (A1A+) - Body ground and other terminals Always 10 kΩ or higher
C87-4 (A1A-) or C92-97 (A1A-) - Body ground and other terminals Always 10 kΩ or higher
C88-1 (HA2A) or C92-45 (HA2A) - Body ground and other terminals Always 10 kΩ or higher
C88-3 (A2A+) or C92-121 (A2A+) - Body ground and other terminals Always 10 kΩ or higher
C88-4 (A2A-) or C92-120 (A2A-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Input the DTC: P223711, P223712, P223713, P223716, P223717, P22371B, P224011, P224012, P224013, P224016, P224017, P22401B, P225111, P225112, P225411 or P225412.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

g.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P223711, P223712, P223713, P223716, P223717, P22371B, P224011, P224012, P224013, P224016, P224017, P22401B, P225111, P225112, P225411 or P225412 is output)
B




A

END

B