The drive start control is controlled by the ECM.
If the ECM determines that the shift lever and accelerator pedal are operated abnormally, engine output is restricted and, when necessary, a warning is displayed on the combination meter assembly.
Even if the accelerator pedal is maintained, the engine output may increase when driving uphill and decrease when driving downhill. This is due to the drive start control controlling the engine output, and is not a malfunction.
Check if the customer operated the vehicle in a way that would cause the drive start control to operate.
Pattern A (When all of the following conditions are met, control starts.)
The accelerator pedal is open by approximately 1/5 or more.
The shift lever is moved from P to any forward position D (other forward shift position) or R.
Pattern B (When all of the following conditions are met, control starts.)
The accelerator pedal is open by approximately 1/5 or more.
The shift lever is moved from R to any forward position D (other forward shift position), any forward position D (other forward shift position) to R, or N to R.
Operation may not be possible in certain situations.
Items Controlled
Engine output is restricted.
Deactivation Conditions
The accelerator pedal is released.
The shift lever is in P or N.
The restraint level for engine output differs for pattern A and pattern B.
Engine output is corrected according to the slope incline when control is in operation.
Control will not operate when TRC operation is stopped.
Control will also not operate under the following conditions.
When in auto LSD mode
When the transfer switch is operated to switch the status to L4
When the center differential is locked
When multi-terrain select is selected
| Result | Proceed to |
|---|---|
| Performed | A |
| Not performed | B |
A
B
Turn the ignition switch to ON.
Enter the following menus: System Select / Health Check.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output (Hunting) | A |
| DTCs are not output (Hesitation/poor acceleration) | B |
| DTCs are output | C |
A
B
C
Start the engine.
Read the value displayed on the GTS.
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
| RR Wheel Speed |
| RL Wheel Speed |
| GTS Display | Condition | Specified Condition |
|---|---|---|
| FR Wheel Speed FL Wheel Speed RR Wheel Speed RL Wheel Speed |
Vehicle stopped, engine running | 0 km/h (0 mph) |
| Vehicle being driven at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) | No large fluctuations when driving at a constant speed |
When performing a drive test, obey all speed limits and traffic laws.
The data while driving can be stored by using the GTS data store function.
The stored data can be checked after driving.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Start the engine.
Read the value displayed on the GTS.
| Tester Display |
|---|
| Forward and Rearward G |
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Forward and Rearward G | During deceleration | Value changes with vehicle speed |
| During acceleration | Value changes with vehicle speed |
When performing a drive test, obey all speed limits and traffic laws.
The data while driving can be stored by using the GTS data store function.
The stored data can be checked after driving.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the park/neutral position switch assembly.
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| Normal | A |
| Abnormal | B |
A
B
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Turn the ignition switch to ON.
Read the value displayed on the GTS.
| Tester Display |
|---|
| Accelerator Position Sensor No.1 Voltage % |
| Accelerator Position Sensor No.2 Voltage % |
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Accelerator Position Sensor No.1 Voltage % | Accelerator Pedal Released → Depressed | Values smoothly change following accelerator pedal operation |
| Accelerator Position Sensor No.2 Voltage % |
For numerical values of Accelerator Position Sensor No.1 Voltage % and Accelerator Position Sensor No.2 Voltage %, refer to the Data List.
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
| Proceed to |
|---|
| OK |
| NG |
OK
NG