Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P243011  AIR System Air Flow/Pressure Sensor Circuit Low Bank 1 Circuit Short to Ground  P243015  AIR System Air Flow/Pressure Sensor Circuit High Bank 1 Circuit Short to Battery or Open  P24301C  AIR System Air Flow/Pressure Sensor Circuit Range/Performance Bank 1 Circuit Voltage Out of Range  P243511  AIR System Air Flow/Pressure Sensor Circuit Low Bank 2 Circuit Short to Ground  P243515  AIR System Air Flow/Pressure Sensor Circuit High Bank 2 Circuit Short to Battery or Open  P24351C  AIR System Air Flow/Pressure Sensor Circuit Range/Performance Bank 2 Circuit Voltage Out of Range  


DESCRIPTION

Refer to DTC P041211.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P041211

Refer to DTC P041512.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P041512

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P243011 AIR System Air Flow/Pressure Sensor Circuit Low Bank 1 Circuit Short to Ground While the engine is running, voltage output of the pressure sensor is below 0.5 V (1 trip detection logic).
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM


Comes on SAE: P2432
P243015 AIR System Air Flow/Pressure Sensor Circuit High Bank 1 Circuit Short to Battery or Open While the engine is running, voltage output of the pressure sensor is higher than 4.5 V (1 trip detection logic)
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM


Comes on SAE: P2433
P24301C AIR System Air Flow/Pressure Sensor Circuit Range/Performance Bank 1 Circuit Voltage Out of Range Pressure sensor indicates a value below 45.6 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) for 5 seconds or more (2 trip detection logic).
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM


Comes on SAE: P2431
P243511 AIR System Air Flow/Pressure Sensor Circuit Low Bank 2 Circuit Short to Ground While the engine is running, voltage output of the pressure sensor is below 0.5 V (1 trip detection logic).
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM


Comes on SAE: P2437
P243515 AIR System Air Flow/Pressure Sensor Circuit High Bank 2 Circuit Short to Battery or Open While the engine is running, voltage output of the pressure sensor is higher than 4.5 V (1 trip detection logic)
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM


Comes on SAE: P2438
P24351C AIR System Air Flow/Pressure Sensor Circuit Range/Performance Bank 2 Circuit Voltage Out of Range Pressure sensor indicates a value below 45.6 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) for 5 seconds or more (2 trip detection logic).
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM


Comes on SAE: P2436

MONITOR DESCRIPTION

A085160E48
0.073,2.771 1.125,2.948 1.052,0.177 10 false Pressure Sensor 2.594,2.927 2.917,3.104 0.323,0.177 10 false ECM 2.292,0.833 2.792,1.01 0.5,0.177 10 false VCAI 2.292,1.479 2.656,1.635 0.365,0.156 10 false AIP 0.833,1.615 1.219,1.854 0.385,0.24 10 false AIP 2.292,2.094 2.698,2.292 0.406,0.198 10 false EAIP 0.865,1.031 1.167,1.229 0.302,0.198 10 false VC 0.875,2.208 1.208,2.417 0.333,0.208 10 false E2 0.083,0.042 2.156,0.271 2.073,0.229 10 false Reference (for Bank 1):

The ECM monitors the pressure inside the air passage of the secondary air injection system using the pressure sensor of the air switching valve assembly. If the ECM detects a malfunction in the sensor or sensor circuit, it stores a DTC.

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the GTS initialization is finished.

11.

Perform the System Check operation by pressing Next.

12.

Perform the following to confirm the secondary air injection system pending DTCs: Press Exit.

13.

Enter the following menus: Powertrain / Engine / DTC.

14.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine / Utility / All Readiness.

16.

Input the DTC: P243011, P243015, P24301C, P243511, P243515 or P24351C.

17.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A440807E02
1.688,1.167 1.948,1.365 0.26,0.198 10 false VC 2.01,2.49 2.188,2.688 0.177,0.198 10 false 4 1.656,1.719 1.969,1.906 0.313,0.188 10 false AIP 5.719,1.156 6.156,1.385 0.438,0.229 10 false VCAI 5.719,1.75 6.01,1.938 0.292,0.188 10 false AIP 2.01,1.406 2.188,1.583 0.177,0.177 10 false 2 1.708,2.271 1.969,2.5 0.26,0.229 10 false E2 2.01,1.99 2.188,2.167 0.177,0.177 10 false 3 0.198,2.813 0.5,3 0.302,0.188 10 false C94 0.198,2.99 2.76,3.26 2.563,0.271 10 false Emission Control Valve Set (for Bank 1) 1.615,3.719 1.938,3.938 0.323,0.219 10 false VC2 2,5.031 2.198,5.229 0.198,0.198 10 false 4 1.594,4.281 1.938,4.49 0.344,0.208 10 false AIP2 2,3.906 2.208,4.146 0.208,0.24 10 false 2 1.646,4.813 1.958,5.021 0.313,0.208 10 false E22 1.99,4.49 2.167,4.719 0.177,0.229 10 false 3 0.219,5.365 0.542,5.573 0.323,0.208 10 false C95 5.438,1.156 5.667,1.385 0.229,0.229 10 false 75 5.427,1.708 5.604,1.885 0.177,0.177 10 false 73 5.74,4.271 6.146,4.5 0.406,0.229 10 false AIP2 5.438,4.271 5.667,4.521 0.229,0.25 10 false 72 5.74,4.823 6.24,5.01 0.5,0.188 10 false EAIP 6.063,5.906 6.438,6.073 0.375,0.167 10 false ECM 5.427,4.802 5.635,5.021 0.208,0.219 10 false 74 6.063,5.75 6.552,5.979 0.49,0.229 10 false C92 0.208,5.542 2.771,5.813 2.563,0.271 10 false Emission Control Valve Set (for Bank 2)

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EMISSION CONTROL VALVE SET)
a.

Disconnect the emission control valve set No. 1 connector.


b.

Disconnect the emission control valve set No. 2 connector.


c.

Turn the ignition switch to ON.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (EMISSION CONTROL VALVE SET - ECM)
2.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - ECM)
a.

Disconnect the pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C94,C92,C95)Location & Routing

Click Connector(C94)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Switching Valve Assembly (for RH Side)

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C95)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Switching Valve Assembly (for LH Side)

C94-3 (AIP) - C92-73 (AIP) Always Below 1 Ω
C94-2 (VC) - C92-75 (VCAI) Always Below 1 Ω
C94-4 (E2) - C92-74 (EAIP) Always Below 1 Ω
C95-3 (AIP2) - C92-72 (AIP2) Always Below 1 Ω
C95-2 (VC2) - C92-75 (VCAI) Always Below 1 Ω
C95-4 (E22) - C92-74 (EAIP) Always Below 1 Ω
C94-3 (AIP) or C92-73 (AIP) - Body ground Always 10 kΩ or higher
C94-2 (VC) or C92-75 (VCAI) - Body ground Always 10 kΩ or higher
C95-3 (AIP2) or C92-72 (AIP2) - Body ground Always 10 kΩ or higher
C95-2 (VC2) or C92-75 (VCAI) - Body ground Always 10 kΩ or higher



d.

Reconnect the pressure sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR)
a.

Turn the ignition switch to ON.


b.

Check the pressure displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Air Pump Pressure (Absolute) Bank 1
Air Pump Pressure (Absolute) Bank 2
50003 372 1019,1020
Standard pressure:

45 to 135 kPa


HINT:

The GTS displays the air pump pressure as an absolute pressure.


Result:
Result Proceed to
OK A
NG (for Bank 1) B
NG (for Bank 2) C




A

B

C

4.CHECK HARNESS AND CONNECTOR (EMISSION CONTROL VALVE SET - ECM)
a.

Disconnect the emission control valve set No. 1 connector.


b.

Disconnect the emission control valve set No. 2 connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C94,C92,C95)Location & Routing

Click Connector(C94)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Switching Valve Assembly (for RH Side)

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C95)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Switching Valve Assembly (for LH Side)

C94-2 (VC) - C92-75 (VCAI) Always Below 1 Ω
C95-2 (VC2) - C92-75 (VCAI) Always Below 1 Ω
C94-2 (VC) or C92-75 (VCAI) - Body ground and other terminals Always 10 kΩ or higher
C95-2 (VC2) or C92-75 (VCAI) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR