Home › Power Source / Network › 1GR-FE (BATTERY / CHARGING) › CHARGING SYSTEM
RM38G0E _57 Power Source / Network _101114 1GR-FE BATTERY / CHARGING _0469187 CHARGING SYSTEM C

1GR-FE BATTERY / CHARGING  CHARGING SYSTEM  P161A87  Lost Communication with Alternator Missing Message  


DESCRIPTION

The ECM communicates with the generator assembly via LIN communication. If a LIN communication error is detected, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Note
P161A87 Lost Communication with Alternator Missing Message Generator assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch ON
(1 trip detection logic)
·

Wire harness or connector

·

Generator assembly

·

ECM


Charge warning is displayed SAE: P161A

HINT:

A charge warning is displayed only when the malfunction continues.


WIRING DIAGRAM

A488796E02
0.583,4.021 1.198,4.344 0.615,0.323 10 false Battery 1.76,0.813 2.375,1.01 0.615,0.198 10 false ALT 3.469,2.635 4.083,2.833 0.615,0.198 10 false B 4.875,2.646 5.49,2.844 0.615,0.198 10 false LIN 3.646,2.396 4.26,2.594 0.615,0.198 10 false 1 4.99,2.396 5.604,2.594 0.615,0.198 10 false 2 4.313,3.615 5.406,3.833 1.094,0.219 10 false IC Regulator 4.146,4.719 5.729,5.031 1.583,0.313 10 false Generator Assembly 1.073,5.417 3.146,5.646 2.073,0.229 10 false : LIN Communication Line 4.583,2.396 5.198,2.594 0.615,0.198 10 false C53 5.948,0.677 6.563,0.875 0.615,0.198 10 false LIN 5.917,2.156 6.531,2.354 0.615,0.198 10 false C92 5.938,1.563 6.552,1.76 0.615,0.198 10 false E1 6.219,2.156 6.594,2.583 0.375,0.427 10 false ECM 5.667,0.51 6.281,0.708 0.615,0.198 10 false 25 5.688,1.438 6.302,1.635 0.615,0.198 10 false 81 3.823,3.542 4.438,3.74 0.615,0.198 10 false P 3.823,4.073 4.448,4.271 0.625,0.198 10 false F 3.823,4.344 4.438,4.542 0.615,0.198 10 false E 3.813,2.906 4.427,3.104 0.615,0.198 10 false B 4.635,2.896 5.25,3.094 0.615,0.198 10 false LIN 3.229,2.396 3.844,2.594 0.615,0.198 10 false C100

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CHARGING SYSTEM

OK

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

NG

REPAIR OR REPLACE CHARGING SYSTEM

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)
a.

Disconnect the C92 ECM connector.


b.

Disconnect the C53 generator assembly connector.




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR