Home › Power Source / Network › 1GR-FE (BATTERY / CHARGING) › GENERATOR
RM38G0E _57 Power Source / Network _101114 1GR-FE BATTERY / CHARGING _0470530 GENERATOR A

1GR-FE BATTERY / CHARGING  GENERATOR  REMOVAL  


CAUTION / NOTICE / HINT

A484869N01
3.583,0.167 5.75,1.25 2.167,1.083 1.167,0.167 2.833,1.25 1.667,1.083 2.396,0.802 2.313,0.417 2.313,0.417 2.229,0.417 false 4.99,0.781 4.833,0.333 4.833,0.333 4.75,0.333 false 4.5,0.667 4.583,0.667 4.583,0.667 4.667,0.865 false 5.167,0.781 5.25,0.583 5.25,0.583 5.333,0.583 false 0.75,1.75 0.833,1.75 0.833,1.75 1,2.167 false 2.354,2.417 2.604,2.417 false 1.479,3.167 1.646,3.167 false 1.802,4.719 1.969,4.719 false 0.469,4.458 0.635,4.458 false 6.698,0.219 6.865,0.219 false 6.667,0.583 6.802,0.583 false 5.771,2.167 6.021,2.167 false 1.208,0.177 1.521,0.375 0.313,0.198 10 false *A 3.625,0.188 3.938,0.385 0.313,0.198 10 false *B 2.021,0.281 2.302,0.635 0.281,0.354 18 false 6 4.573,0.198 4.854,0.552 0.281,0.354 18 false 6 4.333,0.583 4.521,0.792 0.188,0.208 10 false *1 5.396,0.51 5.708,0.708 0.313,0.198 10 false *2 0.594,1.604 0.875,1.958 0.281,0.354 18 false 7 2.677,2.333 2.958,2.688 0.281,0.354 10 false *4 1.26,3.083 1.542,3.438 0.281,0.354 10 false *3 1.573,4.583 1.854,4.938 0.281,0.354 18 false 4 0.271,4.292 0.552,4.646 0.281,0.354 18 false 5 6.51,0.083 6.792,0.438 0.281,0.354 18 false 1 6.49,0.448 6.771,0.802 0.281,0.354 18 false 2 6.094,2.031 6.375,2.385 0.281,0.354 18 false 3 2.74,2.594 3.198,2.792 0.458,0.198 10 false x 2 2.75,5.115 3.208,5.313 0.458,0.198 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 FRONT WHEEL - - - -
4 FRONT FENDER APRON TRIM PACKING D 53785B - - -
5 FAN AND GENERATOR V BELT 16361A - - -
6 NO. 2 IDLER PULLEY SUB-ASSEMBLY 16604 - - -
7 GENERATOR ASSEMBLY 27060 - - -

*A for Integrated Type *B for Separate Type
*1 NO. 2 IDLER PULLEY COVER PLATE *2 IDLER PULLEY COVER PLATE
*3 GENERATOR BRACKET *4 ENGINE WIRE

CAUTION / NOTICE / HINT

The necessary procedures(adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the generator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 3.REMOVE FRONT WHEEL

Hide 53785B 4.REMOVE FRONT FENDER APRON TRIM PACKING D

Hide 16361A 5.REMOVE FAN AND GENERATOR V BELT

Hide 16604 6.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

a.
A484866


Hide 27060 7.REMOVE GENERATOR ASSEMBLY

a.
A484867


b.
A484868