Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM38G0E _58 Vehicle Interior _100886 DOOR LOCK _0468613 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Power Source Circuit  


DESCRIPTION

The main power source for the main body ECU (multiplex network body ECU) is supplied via the door control battery.

WIRING DIAGRAM

B581848E05
1.729,0.5 2.76,0.958 1.031,0.458 10 false from Battery 3.313,0.688 4.094,0.969 0.781,0.281 10 false D/L 2.792,1.552 3.938,1.833 1.146,0.281 10 false ECU-IGR NO. 4 1.396,5.458 4.083,5.719 2.688,0.26 10 false Power Distribution Box Assembly 0.115,5.948 0.729,6.208 0.615,0.26 10 false A 0.094,6.115 3.083,6.385 2.99,0.271 10 false Main Body ECU (Multiplex Network Body ECU) 5.646,5.927 6.26,6.188 0.615,0.26 10 false I72 5.635,6.083 7.094,6.552 1.458,0.469 10 false Door Control Battery 5.75,5.219 6.365,5.479 0.615,0.26 10 false GND1 5.74,4.135 6.354,4.396 0.615,0.26 10 false EDOR 5.75,1.313 6.365,1.573 0.615,0.26 10 false IG 5.75,0.458 6.365,0.719 0.615,0.26 10 false BATB 4.063,0.354 4.677,0.615 0.615,0.26 10 false 35 4.042,0.552 4.656,0.813 0.615,0.26 10 false 5B 4.063,1.229 4.677,1.49 0.615,0.26 10 false 10 4.063,1.417 4.677,1.677 0.615,0.26 10 false 5B 4.042,4.083 4.656,4.344 0.615,0.26 10 false 27 0.479,4.292 1.094,4.552 0.615,0.26 10 false IC 0.917,4.135 1.531,4.396 0.615,0.26 10 false SBAT 1.406,4.146 2.021,4.406 0.615,0.26 10 false 25 5.594,0.448 6.208,0.708 0.615,0.26 10 false 2 5.594,1.313 6.208,1.573 0.615,0.26 10 false 4 5.49,4.135 6.104,4.396 0.615,0.26 10 false 12 5.583,5.219 6.198,5.479 0.615,0.26 10 false 3 5.75,2.188 6.365,2.448 0.615,0.26 10 false DRLY 0.917,2.167 1.531,2.427 0.615,0.26 10 false ACT+ 4.063,2.281 4.677,2.542 0.615,0.26 10 false 5B 4.052,4.281 4.667,4.542 0.615,0.26 10 false 5C 4.073,2.094 4.688,2.354 0.615,0.26 10 false 33 2.292,3.49 4.51,3.792 2.219,0.302 10 false to Each Door Lock Motor 2.219,2.781 3.906,3.083 1.688,0.302 10 false ALL DOOR LOCK 5.594,2.177 6.208,2.438 0.615,0.26 10 false 1 1.396,2.167 2.01,2.427 0.615,0.26 10 false 11 1.625,1.417 2.552,2.01 0.927,0.594 10 false from IGR-NO.1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - POWER SUPPLY AND BODY GROUND)
a.

Disconnect the I72 door control battery connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I72)Location & Routing

Click Connector(I72)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Door Control Battery

I72-2 (BATB) - Body ground Always 11 to 14 V
I72-4 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I72)Location & Routing

Click Connector(I72)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Door Control Battery

I72-3 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK A
NG (GND1 terminal abnormal) B
NG (Other terminal abnormal) C



A

2.CHECK ILLUMINATED ENTRY SYSTEM

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

8.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - POWER DISTRIBUTION BOX ASSEMBLY)
2.CHECK ILLUMINATED ENTRY SYSTEM
a.

a. Check that the illuminated entry system operates normally.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>OPERATION CHECK


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - POWER DISTRIBUTION BOX ASSEMBLY) (DRLY TERMINAL)

NG

5.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - POWER DISTRIBUTION BOX ASSEMBLY) (EDOR TERMINAL)
3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - POWER DISTRIBUTION BOX ASSEMBLY) (DRLY TERMINAL)
a.

Disconnect the I72 door control battery connector.


b.

Disconnect the 5B power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I72)Location & Routing

Click Connector(I72)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Door Control Battery

I72-1 (DRLY) - 5B-33 Always Below 1 Ω
I72-1 (DRLY) or 5B-33 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT DOOR CONTROL BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT DOOR CONTROL BATTERY
a.

Disconnect the 5B power distribution box assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5B-33 - 5B-35 Always Below 1 Ω
5B-33 or 5B-35 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE DOOR CONTROL BATTERY

5.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - POWER DISTRIBUTION BOX ASSEMBLY) (EDOR TERMINAL)
a.

Disconnect the 5C power distribution box assembly connector.


b.

Disconnect the I72 door control battery connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I72)Location & Routing

Click Connector(I72)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Door Control Battery

I72-12 (EDOR) - 5C-27 Always Below 1 Ω
I72-12 (EDOR) or 5C-27 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

b.

c.

Measure the resistance according to the value(s) in the table below.

B581799C05
1.771,0.625 2.271,0.917 0.5,0.292 5.354,0.625 5.854,0.917 0.5,0.292 3.552,2.073 3.354,2.073 3.354,2.073 3.354,1.542 false 3.615,2.01 4.073,2.26 0.458,0.25 10 false SBAT 5.521,0.698 5.76,0.896 0.24,0.198 10 false 5C 2,0.698 2.354,0.896 0.354,0.198 10 false A 0.156,0.052 0.458,0.208 0.302,0.156 10 false *a
*a Component without harness connected
(Power Distribution Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A-25 (SBAT) - 5C-27 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT DOOR CONTROL BATTERY (POWER OUTPUT)

NG

7.INSPECT DOOR CONTROL BATTERY (POWER OUTPUT)
a.

Turn the ignition switch off.


b.

Wait approximately 30 minutes. (Wait for the door control battery discharge to complete.)

HINT:

Depending on the state of charge of the door control battery, the discharge time may be shorter.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I72)Location & Routing

Click Connector(I72)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Door Control Battery

I72-12 (EDOR) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE DOOR CONTROL BATTERY

8.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the I72 door control battery connector.


b.

Disconnect the 5B power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I72)Location & Routing

Click Connector(I72)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Door Control Battery

I72-2 (BATB) - 5B-35 Always Below 1 Ω
I72-4 (IG) - 5B-10 Always Below 1 Ω
I72-2 (BATB) or 5B-35 - Other terminals and body ground Always 10 kΩ or higher
I72-4 (IG) or 5B-10 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR