Home › Steering › STEERING COLUMN › HEATED STEERING WHEEL CONTROLLER
RM38G0E _55 Steering _100923 STEERING COLUMN _0469204 HEATED STEERING WHEEL CONTROLLER A

STEERING COLUMN  HEATED STEERING WHEEL CONTROLLER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C456730N01
3.948,1 4.156,0.708 4.156,0.708 4.323,0.708 true 6.583,2.417 6.417,2.417 6.417,2.417 6.333,2.208 true 5.302,3.458 5.135,3.458 5.135,3.458 5.01,3.177 true 4.417,0.563 4.698,0.917 0.281,0.354 18 false 1 5.552,3.281 5.833,3.635 0.281,0.354 18 false 3 5.813,2.885 6.125,3.083 0.313,0.198 10 false x 3 6.75,0.688 6.99,0.896 0.24,0.208 10 false x 2 6.667,2.302 6.948,2.656 0.281,0.354 18 false 2 5.188,1.271 5.5,1.469 0.313,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STEERING WHEEL ASSEMBLY 45100 - - -
2 STEERING PAD SWITCH ASSEMBLY 84250A - - -
3 MULTIPLEX NETWORK STEERING ECU 864A1A (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the multiplex network steering ECU removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45100 1.REMOVE STEERING WHEEL ASSEMBLY

Hide 84250A 2.DISCONNECT STEERING PAD SWITCH ASSEMBLY

Hide 864A1A 3.REMOVE MULTIPLEX NETWORK STEERING ECU

a.
C456732C01
4.667,3.5 4.833,3.5 4.833,3.5 5.094,2.823 true 6,3.5 5.833,3.5 5.833,3.5 5.5,2.813 true 1.375,3.885 2.063,4.26 0.688,0.375 18 false iii 0.167,0.146 0.521,0.531 0.354,0.385 18 false i 4.083,0.198 4.417,0.531 0.333,0.333 18 false ii 4.5,3.396 4.813,3.594 0.313,0.198 10 false *b 6.021,3.385 6.333,3.583 0.313,0.198 10 false *a
*a Heater Thermistor *b Thermostat
V113147

Remove in this Direction - -


i.

Disconnect 2 connectors.


ii.

Remove the 2 screws, detach the 2 claws and disconnect the steering wheel lower boss cover.

NOTICE:
·

Work carefully to prevent the heater thermistor and thermostat from coming off the steering wheel lower boss cover.

·

If the heater thermistor or thermostat come off the steering wheel lower boss cover, replace the steering wheel assembly.



HINT:

Only loosen the steering wheel lower boss cover. Do not remove it.



iii.

Remove the 3 screws and multiplex network steering ECU.