Home › Steering › STEERING COLUMN › STEERING WHEEL
RM38G0E _55 Steering _100923 STEERING COLUMN _0469200 STEERING WHEEL A

STEERING COLUMN  STEERING WHEEL  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C456093N01
6.583,0.25 6.844,0.25 true 6.448,2.146 6.531,2.396 6.531,2.396 6.698,2.396 true 2.906,1.021 3.104,0.698 3.104,0.698 3.271,0.698 true 4.76,2.469 4.844,2.719 4.844,2.719 5.01,2.719 true 6.115,0.125 6.688,0.458 0.573,0.333 18 false 1, 2 6.781,2.24 7.063,2.594 0.281,0.354 18 false 3 3.594,0.563 3.875,0.917 0.281,0.354 18 false 4 5.115,2.583 5.396,2.938 0.281,0.354 18 false 5 5.458,1.646 5.771,1.844 0.313,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - - - -
3 HORN BUTTON ASSEMBLY 45130 - - -
4 STEERING WHEEL ASSEMBLY 45100 (Click here) - -
5 STEERING PAD SWITCH ASSEMBLY 84250A - - -

C456729N01
0.583,0.25 6.75,2.5 6.167,2.25 0.583,2.5 6.75,4.667 6.167,2.167 4.573,3.719 4.688,3.198 4.688,3.198 4.854,3.198 true 2.885,1.313 3,0.813 3,0.813 3.167,0.813 true 1.677,1.219 1.75,0.833 1.75,0.833 1.917,0.833 true 3.313,0.688 3.594,1.042 0.281,0.354 18 false 6 5.167,3.073 5.448,3.427 0.281,0.354 18 false 7 5.417,3.531 5.875,3.729 0.458,0.198 10 false x 3 3.708,1.104 4.167,1.302 0.458,0.198 10 false x 3 6.323,1.698 6.781,1.896 0.458,0.198 10 false x 2 0.667,2.583 1,2.833 0.333,0.25 10 false *B 0.667,0.333 1,0.583 0.333,0.25 10 false *A 2,0.75 2.333,1 0.333,0.25 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

6 MULTIPLEX NETWORK STEERING ECU (w/o Steering Heater) 864A1A - - -
7 MULTIPLEX NETWORK STEERING ECU (w/ Steering Heater) 864A1A (Click here) - -

*A w/o Steering Heater *B w/ Steering Heater
*1 LOWER STEERING WHEEL BOSS COVER - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the steering wheel assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

Click here(Click here)

Hide 45130 3.REMOVE HORN BUTTON ASSEMBLY

Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

a.
C456094C01
6.24,0.365 6.552,0.323 6.552,0.323 6.24,0.281 true 4.094,3.344 4.833,3 4.833,3 5,3 true 4.156,3.552 4.833,3 true 4.583,3.75 4.833,3.021 true 4.156,3.396 4.833,3 true 6.615,0.24 6.823,0.417 0.208,0.177 10 true *a 0.25,0.135 0.5,0.417 0.25,0.281 18 true i 4.177,0.115 4.448,0.406 0.271,0.292 18 true ii 2.667,3.198 2.917,3.479 0.25,0.281 18 true iii 4.469,5.063 4.781,5.26 0.313,0.198 10 false *b 2.823,5.292 3.135,5.49 0.313,0.198 10 false *c 5.083,2.938 5.5,3.219 0.417,0.281 10 false SST
*a Matchmark *b Turn
*c Hold - -


i.

Disconnect each connector.


ii.

Using a socket hexagon wrench (10 mm), remove the bolt, and place matchmarks on the steering wheel assembly and the steering column assembly.


iii.

Using SST, remove the steering wheel assembly.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05070, 09957-04010)
09950-60011  (09951-00220)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.




Hide 84250A 5.REMOVE STEERING PAD SWITCH ASSEMBLY

Hide 864A1A 6.REMOVE MULTIPLEX NETWORK STEERING ECU (w/o Steering Heater)

Hide 864A1A 7.REMOVE MULTIPLEX NETWORK STEERING ECU (w/ Steering Heater)

Z101186

Click here(Click here)