Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467925 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Cooling Box Control Switch Circuit  


DESCRIPTION

The control switch assembly is the activation switch for the cool box. If the cool box does not activate when the cooler control switch is pushed, there may be a malfunction in the circuit shown below.

WIRING DIAGRAM

E459614E01
5.021,0.292 5.198,0.49 0.177,0.198 10 false 6 5.031,1.917 5.208,2.115 0.177,0.198 10 false 1 4.958,2.469 5.198,2.677 0.24,0.208 10 false 12 2.427,0.302 2.604,0.5 0.177,0.198 10 false 2 2.427,0.615 2.604,0.813 0.177,0.198 10 false 5 3.948,1.635 4.99,1.875 1.042,0.24 10 false ECU-IGP NO.3 2.281,1.458 3.635,1.667 1.354,0.208 10 false from IGP NO.1 Relay 5.271,3.042 6.854,3.438 1.583,0.396 10 false Air Conditioning Amplifier Assembly (for Cool Box) 0.99,1.208 3.469,1.417 2.479,0.208 10 false Control Switch Assembly 5.26,2.865 5.719,3.042 0.458,0.177 10 false Q71 0.979,1.052 3.031,1.25 2.052,0.198 10 false Q73 5.021,0.615 5.198,0.813 0.177,0.198 10 false 8 2.833,2.021 4.188,2.229 1.354,0.208 10 false from Battery 3.927,2.198 4.969,2.438 1.042,0.24 10 false ECU-DCC NO.2 5.01,1.333 5.188,1.531 0.177,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY (for Cool Box) - BATTERY AND BODY GROUND)
a.

Disconnect the Q71 air conditioning amplifier assembly (for Cool Box) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q71)Location & Routing

Click Connector(Q71)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooling Box Amplifier (Cooling Box Assembly)

Q71-12 - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(Q71)Location & Routing

Click Connector(Q71)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooling Box Amplifier (Cooling Box Assembly)

Q71-1 - Body ground Always 11 to 14 V
Q71-2 - Body ground Ignition switch off Below 1 V
Q71-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY (for Cool Box) - CONTROL SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY (for Cool Box) - CONTROL SWITCH ASSEMBLY)
a.

Disconnect the Q71 air conditioning amplifier assembly (for Cool Box) connector.


b.

Disconnect the Q73 control switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q71,Q73)Location & Routing

Click Connector(Q71)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooling Box Amplifier (Cooling Box Assembly)

Click Connector(Q73)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Control Switch Assembly

Q71-6 - Q73-2 Always Below 1 Ω
Q71-8 - Q73-5 Always Below 1 Ω
Q71-6 or Q73-2 - Other terminals and body ground Always 10 kΩ or higher
Q71-8 or Q73-5 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT CONTROL SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT CONTROL SWITCH ASSEMBLY

OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (for Cool Box)

NG