Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467925 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Cooling Box Sensor Circuit  


DESCRIPTION

The No. 2 cooler thermistor is installed on the evaporator in the cooling box unit to detect the cooled air temperature that has passed through the evaporator and control the cooling box. It sends appropriate signals to the air conditioning amplifier assembly (for Cool Box). The resistance of the No. 2 cooler thermistor changes in accordance with the cooled air temperature that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly (for Cool Box) applies voltage (12 V) to the No. 2 cooler thermistor and reads voltage changes as the resistance of the No. 2 cooler thermistor changes.

WIRING DIAGRAM

E459613E01
5.052,0.313 5.365,0.51 0.313,0.198 10 false 4 5.052,0.635 5.365,0.833 0.313,0.198 10 false 6 5.052,1.333 5.365,1.531 0.313,0.198 10 false 2 5.052,1.906 5.365,2.104 0.313,0.198 10 false 1 4.979,2.469 5.292,2.667 0.313,0.198 10 false 12 5.302,3.042 6.906,3.469 1.604,0.427 10 false Air Conditioning Amplifier Assembly (for Cool Box) 0.875,1.208 2.51,1.417 1.635,0.208 10 false No. 2 Cooler Thermistor 3.958,1.625 4.948,1.854 0.99,0.229 10 false ECU-IGP NO.3 3.99,2.188 5.104,2.406 1.115,0.219 10 false ECU-DCC NO.2 2.438,0.292 2.75,0.49 0.313,0.198 10 false 1 2.448,0.625 2.76,0.823 0.313,0.198 10 false 2 2.813,2.021 3.688,2.25 0.875,0.229 10 false from Battery 2.292,1.448 3.75,1.656 1.458,0.208 10 false from IGP NO.1 Relay 5.281,2.865 5.646,3.063 0.365,0.198 10 false Q71 0.865,1.031 2.5,1.24 1.635,0.208 10 false Q74

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY (for Cool Box) - BATTERY AND BODY GROUND)
a.

Disconnect the Q71 air conditioning amplifier assembly (for Cool Box) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q71)Location & Routing

Click Connector(Q71)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooling Box Amplifier (Cooling Box Assembly)

Q71-12 - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(Q71)Location & Routing

Click Connector(Q71)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooling Box Amplifier (Cooling Box Assembly)

Q71-1 - Body ground Always 11 to 14 V
Q71-2 - Body ground Ignition switch off Below 1 V
Q71-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY (for Cool Box) - NO. 2 COOLER THERMISTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY (for Cool Box) - NO. 2 COOLER THERMISTOR)
a.

Disconnect the Q71 air conditioning amplifier assembly (for Cool Box) connector.


b.

Disconnect the Q74 No. 2 cooler thermistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q71,Q74)Location & Routing

Click Connector(Q71)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooling Box Amplifier (Cooling Box Assembly)

Click Connector(Q74)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Thermistor (Cooling Box Assembly)

Q71-4 - Q74-1 Always Below 1 Ω
Q71-6 - Q74-2 Always Below 1 Ω
Q71-4 or Q74-1 - Other terminals and body ground Always 10 kΩ or higher
Q71-6 or Q74-2 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 2 COOLER THERMISTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NO. 2 COOLER THERMISTOR

OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (for Cool Box)

NG