Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM38G0E _59 Vehicle Exterior _100826 SLIDING ROOF / CONVERTIBLE _0469275 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2341  Sensor (Motor) Failure  B2344  Position Failure  


DESCRIPTION

When the sliding roof ECU (sliding roof drive gear assembly) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored.

When the sliding roof ECU (sliding roof drive gear assembly) detects a gear position malfunction and the sliding roof operation is stopped, DTC B2344 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2341 Sensor (Motor) Failure Sensor (motor) failure (The sliding roof ECU (sliding roof drive gear assembly) enters fail-safe mode due to a problem with the motor)
·

Sliding roof ECU (Sliding roof drive gear assembly)

·

Sliding roof switch (Map light assembly)

·

Wire harness or connector


Sliding Roof A
B2344 Position Failure Position failure (The sliding roof ECU (sliding roof drive gear assembly) enters fail-safe mode due to a problem with the gear position)
·

Sliding roof ECU (Sliding roof drive gear assembly)

·

Sliding roof switch (Map light assembly)

·

Wire harness or connector


Sliding Roof A

WIRING DIAGRAM

E468263E01
0.5,3.885 2.385,4.365 1.885,0.479 10 false Sliding Roof Switch (Map Light Assembly) 4.521,5.177 6.458,5.542 1.938,0.365 10 false Sliding Roof ECU (Sliding Roof Drive Gear Assembly) 4.531,5.01 4.865,5.26 0.333,0.25 10 false d19 2.49,0.938 2.917,1.219 0.427,0.281 10 false 1 2.5,1.344 2.927,1.625 0.427,0.281 10 false 6 2.5,1.719 2.927,2 0.427,0.281 10 false 2 2.49,2.094 2.917,2.375 0.427,0.281 10 false 7 2.49,2.469 2.917,2.75 0.427,0.281 10 false 24 2.01,1.031 2.438,1.313 0.427,0.281 10 false OPN 2.031,1.417 2.458,1.698 0.427,0.281 10 false CLS 2.125,1.802 2.552,2.083 0.427,0.281 10 false UP 1.875,2.167 2.427,2.469 0.552,0.302 10 false DOWN 1.927,2.552 2.354,2.833 0.427,0.281 10 false GND5 4.177,1.021 4.604,1.302 0.427,0.281 10 false 10 4.25,1.406 4.677,1.688 0.427,0.281 10 false 8 4.25,1.781 4.677,2.063 0.427,0.281 10 false 5 4.25,2.135 4.677,2.417 0.427,0.281 10 false 9 4.26,2.542 4.688,2.823 0.427,0.281 10 false 2 4.427,1.031 4.854,1.313 0.427,0.281 10 false OPN 4.417,1.781 4.844,2.063 0.427,0.281 10 false UP 4.417,1.396 4.844,1.677 0.427,0.281 10 false CLS 4.427,2.167 4.854,2.448 0.427,0.281 10 false DWN 4.427,2.542 4.854,2.823 0.427,0.281 10 false E 2.49,1.135 2.677,1.323 0.188,0.188 10 false d2 2.49,1.5 2.677,1.688 0.188,0.188 10 false d2 2.49,1.885 2.677,2.073 0.188,0.188 10 false d2 2.49,2.271 2.677,2.458 0.188,0.188 10 false d2 2.49,2.646 2.677,2.833 0.188,0.188 10 false d1 1.938,2.927 2.365,3.208 0.427,0.281 10 false GND9 2.5,3.042 2.688,3.229 0.188,0.188 10 false d1 2.479,2.854 2.906,3.135 0.427,0.281 10 false 10

CAUTION / NOTICE / HINT

NOTICE:

If the sliding roof ECU (sliding roof drive gear assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear assembly) must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION



PROCEDURE

1.CHECK SLIDING ROOF OPERATION
a.

Check the sliding roof auto operation.

HINT:

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>OPERATION CHECK


OK:

Auto operation operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK DTC OUTPUT

NG

3.INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
2.CHECK DTC OUTPUT

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Sliding Roof > Clear DTCs
50002 147

Procedure1

b.

Check for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

None



A

B

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

3.INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
a.

Check that the sliding roof ECU (sliding roof drive gear assembly) can be initialized.

HINT:

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION


OK:

Sliding roof ECU (sliding roof drive gear assembly) can be initialized.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC OUTPUT

NG

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY) AND BODY GROUND)
4.CHECK DTC OUTPUT

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Sliding Roof > Clear DTCs
50002 147

Procedure1

b.

Check for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

None



A

END (MALFUNCTION DUE TO INITIALIZATION FAILURE)

B

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY) AND BODY GROUND)

Pre-procedure1

a.

Disconnect the d1 and d2 sliding roof switch (map light assembly) connectors.


b.

Disconnect the d19 sliding roof ECU (sliding roof drive gear assembly) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d19,d2,d1)Location & Routing

Click Connector(d19)Body>No. 1 Roof Wire>Sliding Roof Control ECU (Sliding Roof Drive Gear Assembly)

Click Connector(d2)Body>No. 1 Roof Wire>Map Light Assembly (Front)

Click Connector(d1)Body>No. 1 Roof Wire>Map Light Assembly (Front)

d19-8 (CLS) - d2-6 (CLS) Always Below 1 Ω
d19-8 (CLS) or d2-6 (CLS) - Body ground Always 10 kΩ or higher
d19-10 (OPN) - d2-1 (OPN) Always Below 1 Ω
d19-10 (OPN) or d2-1 (OPN) - Body ground Always 10 kΩ or higher
d19-9 (DWN) - d2-7 (DOWN) Always Below 1 Ω
d19-9 (DWN) or d2-7 (DOWN) - Body ground Always 10 kΩ or higher
d19-5 (UP) - d2-2 (UP) Always Below 1 Ω
d19-5 (UP) or d2-2 (UP) - Body ground Always 10 kΩ or higher
d1-24 (GND5) - Body ground Always Below 1 Ω
d1-10 (GND9) - Body ground Always Below 1 Ω
d19-2 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

6.INSPECT SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)

OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPLACE SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)